参数资料
型号: LM3543MX-H/NOPB
厂商: NATIONAL SEMICONDUCTOR CORP
元件分类: 电源管理
英文描述: 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16
封装: SOIC-16
文件页数: 2/14页
文件大小: 396K
代理商: LM3543MX-H/NOPB
POWER SUPPLY FILTERING
A sizable capacitor should be connected to the input of the
LM3543 to ensure the voltage drop on this node is less than
330 mV during a heavy-load hot-plug event. A 33 F, 16V
tantalum capacitor is recommended. The input supply should
be further bypassed with a 0.01 F - 0.1 F ceramic capacitor,
placed close to the device. The ceramic capacitor reduces
ringing on the supply that can occur when a short is present
at the output of a port.
EXTENDING THE FAULT FLAG DELAY
While the 7 ms (typical) internal delay in reporting flag condi-
tions is adequate for most applications, the delay can be
extended by connecting external RC filters to the FLAG pins,
as shown in Figure 5.
10125828
FIGURE 5. Typical Circuit for Lengthening the Internal
Flag Delay
POWER DISSIPATION AND JUNCTION TEMPERATURE
A few simple calculations will allow a designer to calculate the
approximate operating temperature of the LM3543 for a given
application. The large currents possible through the low re-
sistance power MOSFET combined with the high thermal
resistance of the SOIC package, in relation to power pack-
ages, make this estimate an important design step.
Begin the estimate by determining R
ON at the expected op-
erating temperature using the graphs in the Typical Perfor-
mance Characteristics section of this datasheet. Next,
calculate the power dissipation through the switch with Equa-
PD = R
ON * IDS
2
(1)
Note:
Equation for power dissipation neglects portion that
comes from LM3543 quiescent current because this value will
almost always be insignificant.
Using this figure, determine the junction temperature with
T
J = PD * θJA + TA.
(2)
Where:
θ
JA = SOIC Thermal Resistance: 130°C/W and TA = Ambient
Temperature (°C).
Compare the calculated temperature with the expected tem-
perature used to estimate R
ON. If they do not reasonably
match, re-estimate R
ON using a more appropriate operating
temperature and repeat the calculations. Reiterate as neces-
sary.
PCB LAYOUT CONSIDERATIONS
In order to meet the USB requirements for voltage drop, droop
and EMI, each component used in this circuit must be evalu-
ated for its contribution to the circuit performance. These
principles are illustrated in Figure 6. The following PCB layout
rules and guidelines are recommended
1.
Place the switch as close to the USB connector as
possible. Keep all V
bus traces as short as possible and
use at least 50-mil, 1 ounce copper for all V
bus traces.
Solder plating the traces will reduce the trace resistance.
2.
Avoid vias as much as possible. If vias are used, use
multiple vias in parallel and/or make them as large as
possible.
3.
Place the output capacitor and ferrite beads as close to
the USB connector as possible.
4.
If ferrite beads are used, use wires with minimum
resistance and large solder pads to minimize connection
resistance.
10125827
FIGURE 6. Self-Powered Hub Connections and Per-Port Voltage Drop
www.national.com
10
101258 Version 5 Revision 6
Print Date/Time: 2010/02/04 15:48:33
LM3543
相关PDF资料
PDF描述
LM3686TL-AADW 1.375 A SWITCHING REGULATOR, 3400 kHz SWITCHING FREQ-MAX, PBGA12
LM385BZX 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, PBCY3
LM285ZX 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, PBCY3
LM285BXZX 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, PBCY3
LM385BYZX 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, PBCY3
相关代理商/技术参数
参数描述
LM3543MX-L 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述:
LM3543MX-L/NOPB 制造商:Texas Instruments 功能描述:USB Power SW Hi Side/DIST Triple 5.5V 2A 16-Pin SOIC N T/R
LM3544 制造商:NSC 制造商全称:National Semiconductor 功能描述:Quad Port USB Power Distribution Switch and Over-Current Protection
LM3544B-H E WAF 制造商:Texas Instruments 功能描述:
LM3544M-H 制造商:Texas Instruments 功能描述:2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16