- 您现在的位置：买卖IC网 > PDF目录79685 > LM3622AM-4.2/NOPB (NATIONAL SEMICONDUCTOR CORP) BATTERY CHARGE CONTROLLER, PDSO8 PDF资料下载
参数资料
| 型号： | LM3622AM-4.2/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | BATTERY CHARGE CONTROLLER, PDSO8 |
| 封装： | SOIC-8 |
| 文件页数： | 6/9页 |
| 文件大小： | 190K |
| 代理商： | LM3622AM-4.2/NOPB |
Functional Description
The simplified LM3622 block diagram in Figure 1 gives a
general idea of the circuit operation. The controller integrates
the reference, feedback and drive functions on-chip to con-
trol a linear, lithium-ion battery charger in constant voltage
and constant current (CVCC) charge operation. The regu-
lated output voltage is sensed between CEL and CS, and the
battery charge current is sensed across a current-sense
resistor between CS and GND. The EXT pin is designed for
driving a series pass element, which can be a PNP transistor
or a P-MOSFET.
Tying the LV
ENB pin to ground enables the controller’s low-
voltage detection circuit. When the low-voltage detection
circuit is enabled and a battery voltage below a preset
threshold is detected, the LM3622 will drive the LV pin low
and shut off the current flowing into the EXT pin to suspend
the CVCC charge process. The low-voltage threshold is user
selectable to be either 2.15V/cell or 2.7V/cell by pulling the
LV
SEL pin to GND or VCC respectively. The LV pin is a NPN
open collector output that can be used to turn on a low
current source to wake up charge a deeply depleted battery.
When the low-voltage detection is disabled (LV
ENB pulled up
to V
CC), the LM3622 always starts the charge cycle in con-
stant current mode at any battery voltage below the control-
ler’s regulation level, and maintains the LV pin at a high-
impedance state.
Application Information
CEL PIN CURRENT DRAIN
The LM3622 has an internal power down switch in series
with the on-chip resistor divider that is used for sensing the
battery voltage. In the event that the V
CC supply is removed,
the power down switch will disconnect the resistor divider
from the CS pin, preventing the battery from discharging
through the CEL pin.
EXT PIN
The EXT pin is internally pulled up to V
CC via a 20A current
source making it possible to eliminate the external base-
emitter resistor when driving a PNP transistor, or the gate-
source resistor when driving a P-MOSFET. However, the
voltage applied to EXT is not allowed to be higher than (V
CC
+ 0.3V), otherwise the reverse current from EXT pin to V
CC
pin may cause damage to the device.
LV PIN CURRENT RATING
The LV pin is a low power, NPN open collector output that is
rated to sink 10mA maximum. Therefore, the value of the pull
up resistor should be chosen high enough to limit the current
to be less than 10mA.
CS PIN
In normal operation, the current limit threshold voltage for
the CS pin is 100mV typical. In case of a fault condition, the
voltage to this pin should be limited to below 5V.
10097411
FIGURE 1. LM3622 Simplified Block Diagram
LM3622
www.national.com
6
相关PDF资料 |
PDF描述 |
|---|---|
| LM199AH/NOPB | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 6.95 V, MBCY4 |
| LTC4266AIUHF-2#TRPBF | POWER SUPPLY MANAGEMENT CKT, PQCC38 |
| LM2574HV-15BWMT&R | SWITCHING REGULATOR, 52 kHz SWITCHING FREQ-MAX, PDSO14 |
| LME0312S | 1-OUTPUT 0.25 W DC-DC REG PWR SUPPLY MODULE |
| LMB5.2SP | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM3622AM-8.1 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Battery Management |
| LM3622AM-8.2 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Lithium-Ion Battery Charger Controller |
| LM3622AM-8.2/NOPB | 功能描述:IC CTRLR LI-ION BAT CHRG 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LM3622AM-8.4 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| LM3622AM-8.4/NOPB | 功能描述:IC CTRLR LI-ION BAT CHRG 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
发布紧急采购，3分钟左右您将得到回复。