参数资料
型号: LM3622MX-8.4/NOPB
厂商: NATIONAL SEMICONDUCTOR CORP
元件分类: 稳压器
英文描述: BATTERY CHARGE CONTROLLER, PDSO8
封装: SOIC-8
文件页数: 6/9页
文件大小: 190K
代理商: LM3622MX-8.4/NOPB
Functional Description
The simplified LM3622 block diagram in Figure 1 gives a
general idea of the circuit operation. The controller integrates
the reference, feedback and drive functions on-chip to con-
trol a linear, lithium-ion battery charger in constant voltage
and constant current (CVCC) charge operation. The regu-
lated output voltage is sensed between CEL and CS, and the
battery charge current is sensed across a current-sense
resistor between CS and GND. The EXT pin is designed for
driving a series pass element, which can be a PNP transistor
or a P-MOSFET.
Tying the LV
ENB pin to ground enables the controller’s low-
voltage detection circuit. When the low-voltage detection
circuit is enabled and a battery voltage below a preset
threshold is detected, the LM3622 will drive the LV pin low
and shut off the current flowing into the EXT pin to suspend
the CVCC charge process. The low-voltage threshold is user
selectable to be either 2.15V/cell or 2.7V/cell by pulling the
LV
SEL pin to GND or VCC respectively. The LV pin is a NPN
open collector output that can be used to turn on a low
current source to wake up charge a deeply depleted battery.
When the low-voltage detection is disabled (LV
ENB pulled up
to V
CC), the LM3622 always starts the charge cycle in con-
stant current mode at any battery voltage below the control-
ler’s regulation level, and maintains the LV pin at a high-
impedance state.
Application Information
CEL PIN CURRENT DRAIN
The LM3622 has an internal power down switch in series
with the on-chip resistor divider that is used for sensing the
battery voltage. In the event that the V
CC supply is removed,
the power down switch will disconnect the resistor divider
from the CS pin, preventing the battery from discharging
through the CEL pin.
EXT PIN
The EXT pin is internally pulled up to V
CC via a 20A current
source making it possible to eliminate the external base-
emitter resistor when driving a PNP transistor, or the gate-
source resistor when driving a P-MOSFET. However, the
voltage applied to EXT is not allowed to be higher than (V
CC
+ 0.3V), otherwise the reverse current from EXT pin to V
CC
pin may cause damage to the device.
LV PIN CURRENT RATING
The LV pin is a low power, NPN open collector output that is
rated to sink 10mA maximum. Therefore, the value of the pull
up resistor should be chosen high enough to limit the current
to be less than 10mA.
CS PIN
In normal operation, the current limit threshold voltage for
the CS pin is 100mV typical. In case of a fault condition, the
voltage to this pin should be limited to below 5V.
10097411
FIGURE 1. LM3622 Simplified Block Diagram
LM3622
www.national.com
6
相关PDF资料
PDF描述
LFSWGM-TTL-60 SQUARE, 0.06 MHz, WAVEFORM GENERATION, PDIP4
LS1001-7ERD6TB1 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE
LME0509D 1-OUTPUT 0.25 W DC-DC REG PWR SUPPLY MODULE
LX1665CDWT 1.5 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO18
LM3712XSBPX-308 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA9
相关代理商/技术参数
参数描述
LM36274EVM 功能描述:LM36274 4, Non-Isolated Output LED Driver Evaluation Board 制造商:texas instruments 系列:- 零件状态:有效 电流 - 输出/通道:- 输出和类型:4,非隔离 电压 - 输出:- 特性:- 电压 - 输入:2.7 V ~ 5 V 所含物品:板 使用的 IC/零件:LM36274 标准包装:1
LM363 制造商:NSC 制造商全称:National Semiconductor 功能描述:LM363 Precision Instrumentation Amplifier
LM3630A 制造商:TI 制造商全称:Texas Instruments 功能描述:LM3630A High-Efficiency Dual-String White LED Driver
LM3630ATME 制造商:Texas Instruments 功能描述:LED DRVR 20Segment 2.5V/3.3V/5V 12-Pin DSBGA T/R 制造商:Texas Instruments 功能描述:IC LED DRIVER 2-STRING 12DSBGA 制造商:Texas Instruments 功能描述:Hi Eff Dual-String White LED Dvr
LM3630ATMX 制造商:Texas Instruments 功能描述:IC LED DRIVER 2-STRING 12DSBGA 制造商:Texas Instruments 功能描述:LED BACKLIGHT DRIVER 制造商:Texas Instruments 功能描述:LINEAR IC