- 您现在的位置：买卖IC网 > PDF目录30748 > LM3713XTBP-308 (NATIONAL SEMICONDUCTOR CORP) 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, BGA9 PDF资料下载
参数资料
| 型号： | LM3713XTBP-308 |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, BGA9 |
| 封装： | MICRO, BUMP, SMD-9 |
| 文件页数： | 2/13页 |
| 文件大小： | 237K |
| 代理商： | LM3713XTBP-308 |
Circuit Information
Reset Output
The Reset input of a P initializes the device into a known
state. The LM3712/LM3713 microprocessor supervisory cir-
cuits assert a forced reset output to prevent code execution
errors during power-up, power-down, and brownout condi-
tions.
RESET is guaranteed valid for V
CC > 1V. Once VCC ex-
ceeds the reset threshold, an internal timer maintains the
output for the reset timeout period. After this interval, reset
goes high. The LM3712 offers an active-low RESET; The
LM3713 offers an active-high RESET.
Any time V
CC drops below the reset threshold (such as
during a brownout), the reset activates. When V
CC again
rises above the reset threshold, the internal timer starts.
Reset holds until V
CC exceeds the reset threshold for longer
than the reset timeout period. After this time, reset releases.
The Manual Reset input (MR) will initiate a forced reset also.
See the Manual Reset Input section.
Reset Threshold
The LM3712/LM3713 family is available with a reset voltage
of 3.08V. Other reset thresholds in the 2.20V to 5.0V range,
in steps of 10 mV, are available; contact National Semicon-
ductor for details.
Manual Reset Input (MR)
Many P-based products require a manual reset capability,
allowing the operator to initiate a reset. The MR input is fully
debounced and provides an internal 56 k
pull-up. When the
MR input is pulled below V
MRT (1.225V) for more than 25 s,
reset is asserted after a typical delay of 12 s. Reset remains
active as long as MR is held low, and releases after the reset
timeout period expires after MR rises above V
MRT. Use MR
with digital logic to assert or to daisy chain supervisory
circuits. It may be used as another low-line comparator by
adding a buffer.
Power-Fail Comparator (PFI/PFO)
The PFI is compared to a 1.225V internal reference, V
PFT.If
PFI is less than V
PFT, the Power Fail Output PFO drops low.
The power-fail comparator signals a falling power supply,
and is driven typically by an external voltage divider that
senses either the unregulated supply or another system
supply voltage. The voltage divider generally is chosen so
the voltage at PFI drops below V
PFT several milliseconds
before the main supply voltage drops below the reset thresh-
old, providing advanced warning of a brownout.
The voltage threshold is set by R
1 and R2 and is calculated
as follows:
Note this comparator is completely separate from the rest of
the circuitry, and may be employed for other functions as
needed.
Watchdog Timer Input (WDI)
The watchdog timer input monitors one of the microproces-
sor’s output lines for activity. Each time a transition occurs on
this monitored line, the watchdog counter is reset. However,
if no transition occurs and the timeout period is reached, the
LM3712/LM3713 assumes that the microprocessor has
locked up and the watchdog output WDO, is activated.
WDI is a high impedance input. WDO is an active-low totem
pole output.
Special Precautions for the micro SMD Package
As with most integrated circuits, the LM3712 and LM3713
are sensitive to exposure from visible and infrared (IR) light
radiation. Unlike a plastic encapsulated IC, the micro SMD
package has very limited shielding from light, and some
sensitivity to light reflected from the surface of the PC board
or long wavelength IR entering the die from the side may be
experienced. This light could have an unpredictable affect on
the electrical performance of the IC. Care should be taken to
shield the device from direct exposure to bright visible or IR
light during operation.
Micro SMD Mounting
The micro SMD package requires specific mounting tech-
niques which are detailed in National Semiconductor Appli-
cation Note AN-1112. Referring to the section Surface
Mount Technology (SMT) Assembly Considerations,it
should be noted that the pad style which must be used with
the 9-pin package is the NSMD (non-solder mask defined)
type.
For best results during assembly, alignment ordinals on the
PC board may be used to facilitate placement of the micro
SMD device.
LM3712/LM3713
www.national.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| LM3713XVBP-308 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, BGA9 |
| LM3712XQBP-308/NOPB | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, BGA9 |
| LM3713XFBPX-308 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, BGA9 |
| LM3713XJBP-308 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, BGA9 |
| LM3713XTBPX-308 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, BGA9 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM3722-9 | 制造商:Power-One 功能描述:LM Series Triple Output 5.4V 12V 12V AC/DC Converter |
| LM3722A-2.32 E WAF | 制造商:Texas Instruments 功能描述: |
| LM3722A-3.08 E WAF | 制造商:Texas Instruments 功能描述: |
| LM3722A-4.63 E WAF | 制造商:Texas Instruments 功能描述: |
| LM3722EM5-2.32 | 制造商:Texas Instruments 功能描述:RESET CIRCUIT SMD SOT23-5 3722 |
发布紧急采购，3分钟左右您将得到回复。