参数资料
型号: LM3724I2.32MWC
厂商: NATIONAL SEMICONDUCTOR CORP
元件分类: 电源管理
英文描述: 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC
封装: WAFER
文件页数: 23/24页
文件大小: 398K
代理商: LM3724I2.32MWC
Timing Diagram
20014412
Circuit Information
Reset Output
The reset input of a P initializes the device into a known
state. The LM3722/LM3723/LM3724 microprocessor voltage
monitoring circuits assert a forced reset output to prevent
code execution errors during power-up, power-down, and
brownout conditions.
RESET is guaranteed valid for V
CC ≥ 1V. Once VCC exceeds
the reset threshold, an internal timer maintains the output for
the reset timeout period. After this interval, reset goes high
and the microprocessor initializes itself into a known state.
The LM3722 and LM3724 offer an active-low RESET; the
LM3723 offers an active-high RESET.
As V
CC drops below the reset threshold (such as during a
brownout), the reset activates (see the
Negative-Going VCC
Transients section). When V
CC again rises above the reset
threshold, the internal timer starts. Reset holds until V
CC
exceeds the reset threshold for longer than the reset timeout
period. After this time, reset releases.
Additionally, the Manual Reset input (MR) will initiate a
forced reset. See the
Manual Reset Input section.
The LM3722/LM3723/LM3724 reset outputs ignore short du-
ration glitches on V
CC and MR. See the Applications Infor-
mation section for details.
Reset Threshold
The LM3722/LM3723/LM3724 are available with reset volt-
ages of 4.63V, 3.08V, and 2.32V which are suitable for
monitoring 5.0V, 3.3V, and 2.5V supplies respectively. Other
reset thresholds in the 2.20V to 5.0V range, in 10 mV steps,
are available; contact National Semiconductor for details.
Manual Reset Input (MR)
Many P-based products require a manual reset capability,
allowing the operator to initiate a reset. The MR input is fully
debounced and provides an internal 22 k
pull-up. When the
MR input is pulled below V
IL (0.25VCC) for more than 100 ns,
reset is asserted after a typical delay of 2 s. Reset remains
active as long as MR is held low, and releases after MR rises
above V
IH and the reset timeout period expires. Use MR with
digital logic to assert reset or to daisy chain supervisory
circuits.
Applications Information
Benefits of Precision Reset Thresholds
A microprocessor supply supervisor must provide a reset
output within a predictable range of the supply voltage. A
common threshold range is between 5% and 10% below the
nominal supply voltage. The 4.63V, 3.08V and 2.32V options
of the LM3722/LM3723/LM3724 use highly accurate circuitry
to ensure that the reset threshold occurs only within this
range (for 5.0V, 3.3V and 2.5V supplies).
Table 1 shows how
the standard reset thresholds apply to 5.0V, 3.3V, and 2.5V
nominal supply voltages.
LM3722/LM3723/LM3724
www.national.com
8
相关PDF资料
PDF描述
LM3722E3.08MDC 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC
LM3724I2.32MDC 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC
LM3722I2.32MDC 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC
LM3723I3.08MWC 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC
LM3723E4.63MDC 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC
相关代理商/技术参数
参数描述
LM3724IM5-2.32 制造商:Texas Instruments 功能描述:RESET CIRCUIT SMD 3724 SOT-23-5 制造商:Texas Instruments 功能描述:RESET CIRCUIT, SMD, 3724, SOT-23-5
LM3724IM5-2.32 制造商:Texas Instruments 功能描述:RESET CIRCUIT SMD 3724 SOT-23-5
LM3724IM5-2.32/NOPB 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
LM3724IM5232NOPB 制造商:NATIONAL 功能描述:2 partial reels
LM3724IM5-3.08 制造商:Texas Instruments 功能描述:Processor Supervisor 3.08V 2.5V/3.3V/5V 5-Pin SOT-23 T/R 制造商:Texas Instruments 功能描述:RESET CIRCUIT SMD 3724 SOT-23-5 制造商:Texas Instruments 功能描述:RESET CIRCUIT, SMD, 3724, SOT-23-5