- 您现在的位置：买卖IC网 > PDF目录30749 > LM3822MM-2.0/NOPB (NATIONAL SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, PDSO8 PDF资料下载
参数资料
| 型号： | LM3822MM-2.0/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| 封装： | MSOP-8 |
| 文件页数： | 2/13页 |
| 文件大小： | 312K |
| 代理商： | LM3822MM-2.0/NOPB |
PWM Output and Current
Accuracy
OFFSET
The PWM output is quantized to 1024 levels. Therefore, the
duty cycle can change only in increments of 1/1024.
There is a one-half (0.5) quantization cycle delay in the
output of the PWM circuitry. That is to say that instead of a
duty cycle of N/1024, the duty cycle actually is (N+12)/1024.
The quantization error can be corrected for if a more precise
result is desired. To correct for this error, simply subtract
1/2048 from the measured duty cycle.
The extra half cycle delay will show up as a DC offset of 12
bit if it is not corrected for. This is approximately 1.0 mA for
1.0 Amp parts, and 10 mA for 2.0 Amp parts.
JITTER
In addition to quantization, the duty cycle will contain some
jitter. The jitter is quite small (for example, the standard
deviation of jitter is only 0.1% for the LM3822-1.0). Statisti-
cally the jitter can cause an error in a current sample. Be-
cause the jitter is a random variable, the mean and standard
deviation are used. The mean, or average value, of the jitter
is zero. The standard deviation (0.1%) can be used to define
the peak error caused from jitter.
The “crest factor” has often been used to define the maxi-
mum error caused by jitter. The crest factor defines a limit
within which 99.7% of the samples fall. The crest factor is
defined as ±0.3% error in the duty cycle.
Since the jitter is a random variable, averaging multiple
outputs will reduce the effective jitter. Obeying statistical
laws, the jitter is reduced by the square root of the number of
readings that are averaged. For example, if four readings of
the duty cycle are averaged, the resulting jitter (and crest
factor) are reduced by a factor of two.
JITTER AND NOISE
Jitter in the PWM output appears as noise in the current
measurement. The Electrical Characteristics show noise
measured in current RMS (root mean square). Arbitrarily one
could specify PWM jitter, as opposed to noise. In either case
the effect results in a random error in an individual current
measurement.
Noise, just like jitter, can be reduced by averaging many
readings. The RMS value of the noise corresponds to one
standard deviation. The “crest factor” can be calculated in
terms of current, and is equal to ±3 sigma (RMS value of the
noise).
Noise will also be reduced by averaging multiple readings,
and follows the statistical laws of a random variable.
ACCURACY VERSUS NOISE
The graph shown in Figure 5 illustrates the typical response
of ±1 Ampere current gauges. In this graph, the horizontal
axis indicates time, and the vertical axis indicates measured
current (the PWM duty cycle has been converted to current).
The graph was generated for an actual current of 500 mA.
The difference between successive readings manifests itself
as jitter in the PWM output or noise in the current measure-
ment (when duty cycle of the PWM output is converted to
current).
The accuracy of the measurement depends on the noise in
the current waveform. The accuracy can be improved by
averaging several outputs. Although there is variation in
successive readings, a very accurate measurement can be
obtained by averaging the readings. For example, on aver-
aging the readings shown in this example, the average
current measurement is 502.3 mA (Figure 5). This value is
very close to the actual value of 500 mA. Moreover, the
accuracy depends on the number of readings that are aver-
aged.
LOW CURRENT MEASUREMENTS
The DC offset of the LM3822-1.0 is typically under 1 mA.
This low offset allows accurate low current measurements.
Even currents in the 10 mA range can be measured with
accuracies typically better than ±5%.
10124926
FIGURE 5. Typical Response of LM3822
LM3822
www.national.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| LM382N | 2 CHANNEL, AUDIO AMPLIFIER, PDIP14 |
| LM382N | VIDEO PREAMPLIFIER, PDIP14 |
| LM385-2.5#TR | SPECIALTY ANALOG CIRCUIT |
| LM385CS-2.5 | SPECIALTY ANALOG CIRCUIT |
| LT1004-1.2#TR | SPECIALTY ANALOG CIRCUIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM3822MMX-1.0 | 功能描述:IC CURRENT GAUGE PRECISION 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳流/电流管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 功能:电流开关 检测方法:- 精确度:±10% 输入电压:1.7 V ~ 5.5 V 电流 - 输出:600mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-UFQFN 供应商设备封装:10-UTQFN（1.4x1.8） 包装:管件 |
| LM3822MMX-2.0 | 功能描述:IC CURRENT GAUGE PRECISION 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳流/电流管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 功能:电流开关 检测方法:- 精确度:±10% 输入电压:1.7 V ~ 5.5 V 电流 - 输出:600mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-UFQFN 供应商设备封装:10-UTQFN（1.4x1.8） 包装:管件 |
| LM3824 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Precision Current Gauge IC with Internal Zero Ohm Sense Element and PWM Output |
| LM3824MM-1.0 | 制造商:Texas Instruments 功能描述:Battery Charger 8-Pin MSOP Rail 制造商:Texas Instruments 功能描述:IC CURRENT GAUGE FAST SMD MSOP8 |
| LM3824MM-1.0/NOPB | 功能描述:IC CURRENT GAUGE 3% 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳流/电流管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 功能:电流开关 检测方法:- 精确度:±10% 输入电压:1.7 V ~ 5.5 V 电流 - 输出:600mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-UFQFN 供应商设备封装:10-UTQFN（1.4x1.8） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。