- 您现在的位置：买卖IC网 > PDF目录98001 > LM40CIMT/NOPB (NATIONAL SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, PDSO14 PDF资料下载
参数资料
| 型号： | LM40CIMT/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO14 |
| 封装： | MO-153AB, TSSOP-14 |
| 文件页数： | 19/27页 |
| 文件大小： | 369K |
| 代理商： | LM40CIMT/NOPB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页
3.0 Application Hints (Continued)
3.
Ideally, the LM40 should be placed within 10cm of the
Processor diode pins with the traces being as straight,
short and identical as possible. Trace resistance of 0.7
can cause as much as 1C of error. This error can be
compensated for by adding or subtracting an offset to
the remote temperature reading(s).
4.
Diode traces should be surrounded by a GND guard ring
to either side, above and below if possible. This GND
guard should not be between the D+ and D lines. In the
event that noise does couple to the diode lines it would
be ideal if it is coupled common mode. That is equally to
the D+ and D lines.
5.
Avoid routing diode traces in close proximity to power
supply switching or filtering inductors.
6.
Avoid running diode traces close to or parallel to high
speed digital and bus lines. Diode traces should be kept
at least 2cm apart from the high speed digital traces.
7.
If it is necessary to cross high speed digital traces, the
diode traces and the high speed digital traces should
cross at a 90 degree angle.
8.
The ideal place to connect the LM40’s GND pin is as
close as possible to the Processors GND associated
with the sense diode.
9.
Leakage current between D+ and GND should be kept
to a minimum. Seventeen nano-amperes of leakage can
cause as much as 0.2C of error in the diode tempera-
ture reading (see curve in Section Typical Performance
Characteristics). Keeping the printed circuit board as
clean as possible will minimize leakage current.
The SensorPath Bus is less sensitive to noise than its pre-
decessor the SMBus due to the inherent filtering present in
the pulse-width encoding of the data. Care still needs to be
taken such that induced noise is analyzed and minimized.
SensorPath Bus corrupt data is the most common symptom
for noise coupled in SWD. A no-ACK is the symptom for
noise coupled into the Device Number Select pin (ADD). An
RC lowpass filter as well as a debouncing circuit are in-
cluded in the LM40 that filter noise spikes less than 2.5 sec
in duration on the SWD signal.
LM40
www.national.com
26
相关PDF资料 |
PDF描述 |
|---|---|
| LM4121AI1.2MWA | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.25 V, UUC |
| LM4121AI1.2MDA | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.25 V, UUC |
| LM4121AIADJMWA | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.216 V, UUC |
| LM5000-3MTCX/NOPB | 2.7 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO16 |
| LM5010AHMH | 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO14 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM40CIMTX/NOPB | 功能描述:IC HARDWARE MONITOR 14-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
| LM40F1WE26-A | 制造商:CEC Industries 功能描述:LED BULB, MEDIUM SCREW/E26, AMBER, 1W, Lamp Base Type:Medium Screw / E26, LED Co |
| LM40F1WE26-B | 制造商:CEC Industries 功能描述:LED BULB, MEDIUM SCREW/E26, BLUE, 1W, Lamp Base Type:Medium Screw / E26, LED Col |
| LM40F1WE26-G | 制造商:CEC Industries 功能描述:LED BULB, MEDIUM SCREW/E26, GREEN, 1W, Lamp Base Type:Medium Screw / E26, LED Color:Green, Bulb Size:G-40, Power Rating:1W, Wavelength Typ:525nm, Average Bulb Life:240h, Supply Voltage:240V, Current Rating:100mA, Beam Divergence:360, RoHS Compliant: Yes |
| LM40F1WE26-R | 制造商:CEC Industries 功能描述:LED BULB, MEDIUM SCREW/E26, RED, 1W, Lamp Base Type:Medium Screw / E26, LED Color:Red, Bulb Size:G-40, Power Rating:1W, Wavelength Typ:629nm, Average Bulb Life:240h, Supply Voltage:240V, Current Rating:100mA, Beam Divergence:360 , RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。