- 您现在的位置：买卖IC网 > PDF目录67756 > LM41CIMTX/NOPB (NATIONAL SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, PDSO14 PDF资料下载
参数资料
| 型号： | LM41CIMTX/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO14 |
| 封装： | MO-153AB, TSSOP-14 |
| 文件页数： | 6/27页 |
| 文件大小： | 367K |
| 代理商： | LM41CIMTX/NOPB |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
1.0 Functional Description (Continued)
All devices (master or slave) must monitor the bus for an
Attention Request signal. The following notes clarify the
intended system operation that uses the Attention Request
Indication.
Masters are expected to use the attention request as a
trigger to read results from the LM41. This is done in a
sequence that covers all LM41s. This sequence is re-
ferred to as "master sensor read sequence".
After an Attention Request is sent by an LM41 until after
the next read from the Device Status register the LM41
does not send Attention Requests for a function event
since it is guaranteed that the master will read the Status
register as part of the master sensor read sequence.
Note that the LM41 will send an attention for BER, re-
gardless of the Status register read, to help the master
with any error recovery operations and prevent dead-
locks.
A master must record the Attention Request event. It
must then scan all slave devices in the system by reading
their Device Status register and must handle any pending
event in them before it may assume that there are no
more events to handle.
Note: there is no indication of which slave has sent the
request. The requirement that multiple requests are not sent
allows the master to know within one scan of register reads
that there are no more pending events.
1.3.6 Fixed Device Number Setting
The LM41 device number is defined by strapping of the ADD
pin. The LM41 will wake (after Device Reset) with the Device
Number field of the Device Number register set to the ad-
dress as designated in Section 2.3 "Device Number". It is the
responsibility of the system designer to avoid having two
devices with the same Device Number on the bus.
Devices should be detected by the master by a read opera-
tion of the Device Number register. The read returns "000" if
there is no device at that address on the bus (the EP bit must
be ignored).
LM41
www.national.com
14
相关PDF资料 |
PDF描述 |
|---|---|
| LM5025CCMTE | SWITCHING CONTROLLER, 650 kHz SWITCHING FREQ-MAX, PDSO16 |
| LM5025CSDX | SWITCHING CONTROLLER, DSO16 |
| LM5025CSD | SWITCHING CONTROLLER, DSO16 |
| LM5117PMHX | SWITCHING CONTROLLER, 530 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM5117PSQX | SWITCHING CONTROLLER, 530 kHz SWITCHING FREQ-MAX, QCC24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM41-DH12 | 功能描述:基本/快动开关 Foot Switch RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel |
| LM41-SH12 | 功能描述:基本/快动开关 Foot Switch RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel |
| LM4-2 | 制造商:Banner Engineering 功能描述:PHOTOELECTRIC SENSOR, LOGIC MODULE, Accessory Type:Logic Module, Time Range:0.01 |
| LM420 | 制造商:Banner Engineering 功能描述:LM420 LOGIC MODULE MULTIBEAM 420MA ANALOG MULTIBEAM |
| LM4200 | 制造商:WABER 功能描述: |
发布紧急采购，3分钟左右您将得到回复。