- 您现在的位置：买卖IC网 > PDF目录10491 > LM4819MX (National Semiconductor)IC AMP AUDIO PWR .35W MONO 8SOIC PDF资料下载
参数资料
| 型号： | LM4819MX |
| 厂商： | National Semiconductor |
| 文件页数： | 5/27页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR .35W MONO 8SOIC |
| 标准包装： | 1 |
| 系列： | Boomer® |
| 类型： | AB 类 |
| 输出类型： | 1-通道（单声道） |
| 在某负载时最大输出功率 x 通道数量： | 350mW x 1 @ 16 欧姆 |
| 电源电压： | 2 V ~ 5.5 V |
| 特点： | 消除爆音，差分输入，关闭 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 8-SOIC |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 剪切带 (CT) |
| 其它名称： | *LM4819MX LM4819MXCT |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
SNAS133D – FEBRUARY 2001 – REVISED MARCH 2013
In order to eliminate "clicks and pops", all capacitors must be discharged before turn-on. Rapidly switching VDD
may not allow the capacitors to fully discharge, which may cause "clicks and pops".
AUDIO POWER AMPLIFIER DESIGN EXAMPLE
The following are the desired operational parameters:
Given:
Power Output
100mW
Load Impedance
16
Input Level
1Vrms (max)
Input Impedance
20k
Bandwidth
100Hz–20kHz ± 0.25dB
The design begins by specifying the minimum supply voltage necessary to obtain the specified output power. To
find this minimum supply voltage, use the Output Power vs. Supply Voltage graph in the Typical Performance
Characteristics section. From the graph for a 16
load, (graphs are for 8, 16, and 32 loads) the supply
voltage for 100mW of output power with 1% THD+N is approximately 3.15 volts.
Additional supply voltage creates the benefit of increased headroom that allows the LM4819 to reproduce peaks
in excess of 100mW without output signal clipping or audible distortion. The choice of supply voltage must also
not create a situation that violates maximum dissipation as explained above in the Power Dissipation section. For
example, if a 3.3V supply is chosen for extra headroom then according to Equation 3 the maximum power
dissipation point with a 16
load is 138mW. Using Equation 4 the maximum ambient temperature is 121°C for
the DGK0008A package and 126°C for the D0008A package.
After satisfying the LM4819's power dissipation requirements, the minimum differential gain is found using
(6)
Thus a minimum gain of 1.27 V/V allows the LM4819 to reach full output swing and maintain low noise and
THD+N performance. For this example, let AVD = 1.27. The amplifier's overall gain is set using the input (Ri) and
feedback (RF) resistors. With the desired input impedance set to 20k, the feedback resistor is found using
RF/Ri = AVD/2 (V/V)
(7)
The value of RF is 13k.
The last step in this design example is setting the amplifier's -3dB frequency bandwidth. To achieve the desired
±0.25dB pass band magnitude variation limit, the low frequency response must extend to at least one-fifth the
lower bandwidth limit and the high frequency response must extend to at least five times the upper bandwidth
limit. The gain variation for both response limits is 0.17dB, well with in the ±0.25dB desired limit.
The results are:
fL = 100Hz/5 = 20Hz
fH = 20 kHz*5 = 100kHz
As mentioned in the External Components section, Ri and Ci create a high pass filter that sets the amplifier's
lower band pass frequency limit. Find the coupling capacitor's value using Equation 8.
Ci ≥ 1/(2πRifc) (F)
(8)
Ci ≥ 0.398F, a standard value of 0.39F will be used. The product of the desired high frequency cutoff (100kHz
in this example) and the differential gain, AVD, determines the upper pass band response limit. With AVD = 1.27
and fH = 100kHz, the closed-loop gain bandwidth product (GBWP) is 127kHz. This is less than the LM4819's
900kHz GBWP. With this margin the amplifier can be used in designs that require more differential gain while
avoiding performance restricting bandwidth limitations.
Copyright 2001–2013, Texas Instruments Incorporated
13
相关PDF资料 |
PDF描述 |
|---|---|
| UP050SL110J-KEC | CAP CER 11PF 50V 5% AXIAL |
| VI-25M-IV-B1 | CONVERTER MOD DC/DC 10V 150W |
| VE-2T0-IW-F4 | CONVERTER MOD DC/DC 5V 100W |
| MAX1065BEUI+ | IC ADC 14-BIT 165KSPS 28-TSSOP |
| VE-2T0-IW-F1 | CONVERTER MOD DC/DC 5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM4819MX/NOPB | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LM4820-6 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Fixed Gain 1 Watt Audio Power Amplifier |
| LM4820IBP-6 | 功能描述:IC AMP AUDIO PWR 1W MONO 8USMD RoHS:否 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:Boomer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| LM4820IBPX-6 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Fixed Gain 1 Watt Audio Power Amplifier |
| LM4820ITP-6/NOPB | 功能描述:IC AMP AUDIO PWR 1W MONO 8USMD RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:Boomer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。