- 您现在的位置：买卖IC网 > PDF目录30752 > LM4836MTE/NOPB (NATIONAL SEMICONDUCTOR CORP) 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 PDF资料下载
参数资料
| 型号： | LM4836MTE/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 音频控制 |
| 英文描述： | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 |
| 封装： | TSSOP-28 |
| 文件页数： | 11/28页 |
| 文件大小： | 951K |
| 代理商： | LM4836MTE/NOPB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Application Information (Continued)
the pop is directly proportional to the input capacitor’s size.
Higher value capacitors need more time to reach a quiescent
DC voltage (usually V
DD/2) when charged with a fixed cur-
rent. The amplifier’s output charges the input capacitor
through the feedback resistor, R
f. Thus, pops can be mini-
mized by selecting an input capacitor value that is no higher
than necessary to meet the desired 3dB frequency.
A shown in Figure 1, the input resistor (20k
) and the input
capacitor produce a 3dB high pass filter cutoff frequency
that is found using Equation (7).
(7)
As an example when using a speaker with a low frequency
limit of 150Hz, the input coupling capacitor using Equation
(7), is 0.063F. The 0.33F input coupling capacitor shown
in Figure 1 allows the LM4835 to drive high efficiency, full
range speaker whose response extends below 30Hz.
OPTIMIZING CLICK AND POP REDUCTION
PERFORMANCE
The LM4836 contains circuitry that minimizes turn-on and
shutdown transients or “clicks and pop”. For this discussion,
turn-on refers to either applying the power supply voltage or
when the shutdown mode is deactivated. While the power
supply is ramping to its final value, the LM4836’s internal
amplifiers are configured as unity gain buffers. An internal
current source changes the voltage of the BYPASS pin in a
controlled, linear manner. Ideally, the input and outputs track
the voltage applied to the BYPASS pin. The gain of the
internal amplifiers remains unity until the voltage on the
bypass pin reaches 1/2 V
DD. As soon as the voltage on the
bypass pin is stable, the device becomes fully operational.
Although the BYPASS pin current cannot be modified,
changing the size of C
B alters the device’s turn-on time and
the magnitude of “clicks and pops”. Increasing the value of
C
B reduces the magnitude of turn-on pops. However, this
presents a tradeoff: as the size of C
B increases, the turn-on
time increases. There is a linear relationship between the
size of C
B and the turn-on time. Here are some typical
turn-on times for various values of C
B:
C
B
T
ON
0.01F
2ms
0.1F
20ms
0.22F
44ms
0.47F
94ms
1.0F
200ms
In order eliminate “clicks and pops”, all capacitors must be
discharged before turn-on. Rapidly switching V
DD may not
allow the capacitors to fully discharge, which may cause
“clicks and pops”. In a single-ended configuration, the output
is coupled to the load by C
OUT. This capacitor usually has a
high value. C
OUT discharges through internal 20k
resistors.
Depending on the size of C
OUT, the discharge time constant
can be relatively large. To reduce transients in single-ended
mode, an external 1k
–5k resistor can be placed in par-
allel with the internal 20k
resistor. The tradeoff for using
this resistor is increased quiescent current.
DOCKING STATION
Applications such as notebook computers can take advan-
tage of a docking station to connect to external devices such
as monitors or audio/visual equipment that sends or receives
line level signals. The LM4836 has two outputs, Pin 9 and
Pin 13, which connect to outputs of the internal input ampli-
fiers that drive the volume control inputs. These input ampli-
fiers can drive loads of >1k
(such as powered speakers)
with a rail-to-rail signal. Since the output signal present on
the RIGHT DOCK and LEFT DOCK pins is biased to V
DD/2,
coupling capacitors should be connected in series with the
load. Typical values for the coupling capacitors are 0.33F to
1.0F. If polarized coupling capacitors are used, connect
their "+" terminals to the respective output pin.
Since the DOCK outputs precede the internal volume con-
trol, the signal amplitude will be equal to the input signal’s
magnitude and cannot be adjusted. However, the input am-
plifier’s closed-loop gain can be adjusted using external
resistors. These resistors are shown in Figure 2 as 20k
devices that set each input amplifier’s gain to -1. Use Equa-
tion 8 to determine the input and feedback resistor values for
a desired gain.
-A
v =RF /Ri
(8)
Adjusting the input amplifier’s gain sets the minimum gain for
that channel. The DOCK outputs adds circuit and functional
flexibility because their use supercedes using the inverting
outputs of each bridged output amplifier as line-level out-
puts.
STEREO-INPUT MULTIPLEXER (STEREO MUX)
The LM4836 has two stereo inputs. The MUX CONTROL pin
controls which stereo input is active. Applying 0V to the MUX
CONTROL pin selects stereo input 1. Applying V
DD to the
MUX CONTROL pin selects stereo input 2.
BEEP DETECT FUNCTION
Computers and notebooks produce a system "beep" signal
that drives a small speaker. The speaker’s auditory output
signifies that the system requires user attention or input. To
10108805
FIGURE 2. Resistor for Varying Output Loads
LM4836
www.national.com
19
相关PDF资料 |
PDF描述 |
|---|---|
| LM4836MT/NOPB | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 |
| LM4838MTE/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO28 |
| LM4838MT/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO28 |
| LM4838ITL/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PBGA36 |
| LM4838ITLX/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PBGA36 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM4836MTEX | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LM4836MTEX/NOPB | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LM4836MTX | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Dual Audio Amplifier |
| LM4836MTX/NOPB | 功能描述:IC AMP AUDIO PWR 2.2W AB 28TSSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:Boomer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| LM4837MT | 制造商:Texas Instruments 功能描述: |
发布紧急采购，3分钟左右您将得到回复。