- 您现在的位置：买卖IC网 > PDF目录30753 > LM4851LQ/NOPB (NATIONAL SEMICONDUCTOR CORP) 1.5 W, 3 CHANNEL, AUDIO AMPLIFIER, QCC24 PDF资料下载
参数资料
| 型号： | LM4851LQ/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 1.5 W, 3 CHANNEL, AUDIO AMPLIFIER, QCC24 |
| 封装： | LLP-24 |
| 文件页数： | 9/22页 |
| 文件大小： | 1126K |
| 代理商： | LM4851LQ/NOPB |
Application Information (Continued)
power, higher ambient temperatures are allowed as output
power or duty cycle decreases. If the result of Equation (5) is
greater than that of Equation (6), then decrease the supply
voltage, increase the load impedance, or reduce the ambient
temperature. If these measures are insufficient, a heat sink
can be added to reduce
θ
JA. The heat sink can be created
using additional copper area around the package, with con-
nections to the ground pin(s), supply pin and amplifier output
pins. External, solder attached SMT heatsinks such as the
Thermalloy 7106D can also improve power dissipation.
When adding a heat sink, the
θ
JA is the sum of
θ
JC,
θ
CS, and
θ
SA.(
θ
JC is the junction-to-case thermal impedance,
θ
CS is
the case-to-sink thermal impedance, and
θ
SA is the sink-to-
ambient thermal impedance.) Refer to the Typical Perfor-
mance Characteristics curves for power dissipation informa-
tion at lower output power levels.
POWER SUPPLY BYPASSING
As with any power amplifier, proper supply bypassing is
critical for low noise performance and high power supply
rejection. Applications that employ a 5V regulator typically
use a 10F in parallel with a 0.1F filter capacitors to stabi-
lize the regulator’s output, reduce noise on the supply line,
and improve the supply’s transient response. However, their
presence does not eliminate the need for a local 1.0F
tantalum bypass capacitance connected between the
LM4851’s supply pins and ground. Keep the length of leads
and traces that connect capacitors between the LM4851’s
power supply pin and ground as short as possible. Connect-
ing a 1F capacitor, C
B, between the BYPASS pin and
ground improves the internal bias voltage’s stability and
improves the amplifier’s PSRR. The PSRR improvements
increase as the bypass pin capacitor value increases. Too
large, however, increases turn-on time and can compromise
the amplifier’s click and pop performance. The selection of
bypass capacitor values, especially C
B, depends on desired
PSRR requirements, click and pop performance (as ex-
plained in the section, Proper Selection of External Compo-
nents), system cost, and size constraints.
SELECTING EXTERNAL COMPONENTS
Input Capacitor Value Selection
Amplifying the lowest audio frequencies requires high value
input coupling capacitor (C
i in Figure 1). A high value capaci-
tor can be expensive and may compromise space efficiency
in portable designs. In many cases, however, the speakers
used in portable systems, whether internal or external, have
little ability to reproduce signals below 150Hz. Applications
using speakers with this limited frequency response reap
little improvement by using large input capacitor.
The internal input resistor (R
i) and the input capacitor (Ci)
produce a high pass filter cutoff frequency that is found using
Equation (9).
f
c =1/(2
πR
iCi)
(9)
As an example when using a speaker with a low frequency
limit of 150Hz, C
i, using Equation (9) is 0.063F. The 0.22F
C
i shown in Figure 1 allows the LM4851 to drive high effi-
ciency, full range speaker whose response extends below
40Hz.
Bypass Capacitor Value Selection
Besides minimizing the input capacitor size, careful consid-
eration should be paid to value of C
B, the capacitor con-
nected to the BYPASS pin. Since C
B determines how fast
the LM4851 settles to quiescent operation, its value is critical
when minimizing turn-on pops. The slower the LM4851’s
outputs ramp to their quiescent DC voltage (nominally V
DD/
2), the smaller the turn-on pop. Choosing C
B equal to 1.0F
along with a small value of C
i (in the range of 0.1F to
0.39F), produces a click-less and pop-less shutdown func-
tion. As discussed above, choosing C
i no larger than neces-
sary for the desired bandwidth helps minimize clicks and
pops. C
B’s value should be in the range of 5 times to 7 times
the value of C
i. This ensures that output transients are
eliminated when power is first applied or the LM4851 re-
sumes operation after shutdown.
LM4851
www.national.com
17
相关PDF资料 |
PDF描述 |
|---|---|
| LM4852LQ/NOPB | 1.5 W, 3 CHANNEL, AUDIO AMPLIFIER, QCC24 |
| LM4852ITL/NOPB | 1.1 W, 3 CHANNEL, AUDIO AMPLIFIER, PBGA18 |
| LM4854MT/NOPB | 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
| LM4854MTX/NOPB | 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
| LM4854LD/NOPB | 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM4852 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Integrated Audio Amplifier System |
| LM48520 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Boosted Stereo Class D Audio Power Amplifier with Output Speaker Protection and Spread Spectrum |
| LM48520TL | 制造商:Texas Instruments 功能描述:Audio Amp Speaker 2-CH Stereo 1.3W Class-D 25-Pin uSMD T/R |
| LM48520TL/NOPB | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LM48520TLBD | 功能描述:音频 IC 开发工具 LM48520TLBD EVAL BOARD RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
发布紧急采购，3分钟左右您将得到回复。