- 您现在的位置：买卖IC网 > PDF目录2082 > LM4872ITP/NOPB (National Semiconductor)IC AMP AUDIO PWR 1W MONO 8USMD PDF资料下载
参数资料
| 型号： | LM4872ITP/NOPB |
| 厂商： | National Semiconductor |
| 文件页数： | 3/17页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 1W MONO 8USMD |
| 标准包装： | 1 |
| 系列： | Boomer® |
| 类型： | AB 类 |
| 输出类型： | 1-通道（单声道） |
| 在某负载时最大输出功率 x 通道数量： | 1W x 1 @ 8 欧姆 |
| 电源电压： | 2 V ~ 5.5 V |
| 特点： | 关闭，热保护 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 8-uSMD |
| 封装/外壳： | 8-VFBGA |
| 包装： | 标准包装 |
| 其它名称： | LM4872ITPDKR |
Application Information (Continued)
width is dictated by the choice of external components
shown in Figure 1. The input coupling capacitor, C
i, forms a
first order high pass filter which limits low frequency re-
sponse. This value should be chosen based on needed
frequency response for a few distinct reasons.
Selection Of Input Capacitor Size
Large input capacitors are both expensive and space hungry
for portable designs. Clearly, a certain sized capacitor is
needed to couple in low frequencies without severe attenu-
ation. But in many cases the speakers used in portable
systems, whether internal or external, have little ability to
reproduce signals below 100 Hz to 150 Hz. Thus, using a
large input capacitor may not increase actual system perfor-
mance.
In addition to system cost and size, click and pop perfor-
mance is effected by the size of the input coupling capacitor,
C
i. A larger input coupling capacitor requires more charge to
reach its quiescent DC voltage (nominally 1/2 V
DD). This
charge comes from the output via the feedback and is apt to
create pops upon device enable. Thus, by minimizing the
capacitor size based on necessary low frequency response,
turn-on pops can be minimized.
Besides minimizing the input capacitor size, careful consid-
eration should be paid to the bypass capacitor value. Bypass
capacitor, C
B, is the most critical component to minimize
turn-on pops since it determines how fast the LM4872 turns
on. The slower the LM4872’s outputs ramp to their quiescent
DC voltage (nominally 1/2 V
DD), the smaller the turn-on pop.
Choosing C
B equal to 1.0 F along with a small value of Ci
(in the range of 0.1 F to 0.39 F), should produce a virtually
clickless and popless shutdown function. While the device
will function properly, (no oscillations or motorboating), with
C
B equal to 0.1 F, the device will be much more susceptible
to turn-on clicks and pops. Thus, a value of C
B equal to
1.0 F is recommended in all but the most cost sensitive
designs.
LOW VOLTAGE APPLICATIONS ( BELOW 3.0 V
DD )
The Lm4872 will function at voltages below 3 volts but this
mode of operation requires the addition of a 1k
resistor
from each of the differential output pins ( pins 8 and 4 )
directly to ground. The addition of the pair of 1k
resistors (
R4 & R5 ) assures stable operation below 3 Volt Vdd opera-
tion. The addition of the two resistors will however increase
the idle current by as much as 5mA. This is because at 0v
input both of the outputs of the LM4872’s 2 internal opamps
go to 1/2 V
DD ( 2.5 volts for a 5v power supply ), causing
current to flow through the 1K resistors from output to
ground. See fig 4.
Jumper options have been included on the reference design,
Fig. 4, to accommodate the low voltage application. J2 & J3
connect R4 and R5 to the outputs. J1 operates the shutdown
function. J1 must be installed to operate the part. A switch
may be installed in place of J1 for easier evaluation of the
shutdown function.
AUDIO POWER AMPLIFIER DESIGN
A 1W/8
AUDIO AMPLIFIER
Given:
Power Output
1 Wrms
Load Impedance
8
Input Level
1 Vrms
Input Impedance
20 k
Bandwidth
100 Hz–20 kHz ± 0.25 dB
A designer must first determine the minimum supply rail to
obtain the specified output power. By extrapolating from the
Output Power vs Supply Voltage graphs in the Typical Per-
formance Characteristics section, the supply rail can be
easily found. A second way to determine the minimum sup-
ply rail is to calculate the required V
opeak using Equation 2
and add the output voltage. Using this method, the minimum
supply voltage would be (V
opeak +(VODTOP +VODBOT)), where
V
ODBOT and VODTOP are extrapolated from the Dropout Volt-
age vs Supply Voltage curve in the Typical Performance
Characteristics section.
(2)
Using the Output Power vs Supply Voltage graph for an 8
load, the minimum supply rail is 4.6V. But since 5V is a
standard voltage in most applications, it is chosen for the
supply rail. Extra supply voltage creates headroom that al-
lows the LM4872 to reproduce peaks in excess of 1W with-
out producing audible distortion. At this time, the designer
must make sure that the power supply choice along with the
output impedance does not violate the conditions explained
in the Power Dissipation section.
Once the power dissipation equations have been addressed,
the required differential gain can be determined from Equa-
tion 3.
(3)
R
f/Ri =AVD/2
From Equation 3, the minimum A
VD is 2.83; use AVD =3.
Since the desired input impedance was 20 k
, and with a
A
VD impedance of 2, a ratio of 1.5:1 of Rf to Ri results in an
allocation of R
i =20k
and R
f =30k
. The final design step
is to address the bandwidth requirements which must be
stated as a pair of 3 dB frequency points. Five times away
from a 3 dB point is 0.17 dB down from passband response
which is better than the required ±0.25 dB specified.
f
L = 100 Hz/5 = 20 Hz
f
H =20kHz*5=100 kHz
As stated in the External Components section, R
i in con-
junction with C
i create a highpass filter.
C
i
≥ 1/(2π*20 k*20 Hz) = 0.397 F; use 0.39 F
The high frequency pole is determined by the product of the
desired frequency pole, f
H, and the differential gain, AVD.
With a A
VD = 3 and fH = 100 kHz, the resulting GBWP =
150 kHz which is much smaller than the LM4872 GBWP of
4 MHz. This figure displays that if a designer has a need to
design an amplifier with a higher differential gain, the
LM4872 can still be used without running into bandwidth
limitations.
LM4872
www.national.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| LM4891MX/NOPB | IC AMP AUDIO PWR 1W MONO 8SOIC |
| LMH0002SQE/NOPB | IC CABLE DVR SERIAL DGTL 16-LLP |
| LMH6734MQX/NOPB | IC BUFFER TRPL SELECT 16-SSOP |
| LMK04010BISQ/NOPB | IC CLOCK CONDITIONER W/PLL 48LLP |
| LMV393MUTAG | IC OP AMP DUAL GP LV LV 8-UDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM4872ITPX/NOPB | 制造商:Texas Instruments 功能描述: |
| LM4873 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Dual 2.1W Audio Amplifier Plus Stereo Headphone Function |
| LM4873_02 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Dual 2.1W Audio Amplifier Plus Stereo Headphone Function |
| LM4873IBL | 功能描述:IC AMP AUDIO PWR 3W STER 20USMD RoHS:否 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:Boomer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| LM4873LQ | 制造商:Rochester Electronics LLC 功能描述:DUAL 1.1W AUDIO AMPLIFIER - Bulk |
发布紧急采购，3分钟左右您将得到回复。