- 您现在的位置：买卖IC网 > PDF目录30755 > LM4882MX/NOPB (NATIONAL SEMICONDUCTOR CORP) 0.48 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 PDF资料下载
参数资料
| 型号： | LM4882MX/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 0.48 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| 封装： | SOIC-8 |
| 文件页数： | 14/14页 |
| 文件大小： | 484K |
| 代理商： | LM4882MX/NOPB |
Application Information (Continued)
vice or the shutdown function may cause the “click and pop”
circuitry to not operate fully, resulting in increased “click and
pop” noise.
The value of C
i will also reflect turn-on pops. Clearly, a cer-
tain size for C
i is needed to couple in low frequencies without
excessive attenuation. But in many cases, the speakers
used in portable systems have little ability to reproduce sig-
nals below 100 Hz to 150 Hz. In this case, using a large input
and output coupling capacitor may not increase system per-
formance. In most cases, choosing a small value of C
i in the
range of 0.1 F to 0.33 F, along with C
B equal to 1.0 F
should produce a virtually clickless and popless turn-on. In
cases where C
i is larger than 0.33 F, it may be advanta-
geous to increase the value of C
B. Again, it should be under-
stood that increasing the value of C
B will reduce the “clicks
and pops” at the expense of a longer device turn-on time.
AUDIO POWER AMPLIFIER DESIGN
Design a 250 mW/8
Audio Amplifier
Given:
Power Output
250 mWrms
Load Impedance
8
Input Level
1 Vrms (max)
Input Impedance
20 k
Bandwidth
100 Hz–20 kHz ± 0.50 dB
A designer must first determine the needed supply rail to ob-
tain the specified output power. Calculating the required sup-
ply rail involves knowing two parameters, V
OPEAK and also
the dropout voltage. The latter is typically 530mV and can be
found from the graphs in the Typical Performance Charac-
teristics. V
OPEAK can be determined from Equation 3.
(3)
For 250 mW of output power into an 8
load, the required
V
OPEAK is 2 volts. A minimum supply rail of 4.55V results
from adding V
OPEAK and VOD. Since 5V is a standard supply
voltage in most applications, it is chosen for the supply rail.
Extra supply voltage creates headroom that allows the
LM4882 to reproduce peaks in excess of 300 mW without
clipping the signal. At this time, the designer must make sure
that the power supply choice along with the output imped-
ance does not violate the conditions explained in the Power
Dissipation section.
Once the power dissipation equations have been addressed,
the required gain can be determined from Equation 4.
(4)
A
V =Rf /Ri
(5)
From Equation 4, the minimum gain is:
A
V = 1.4
Since the desired input impedance was 20 k
, and with a
gain of 1.4, a value of 28 k
is designated for R
f, assuming
5% tolerance resistors. This combination results in a nominal
gain of 1.4. The final design step is to address the bandwidth
requirements which must be stated as a pair of 3 dB fre-
quency points. Five times away from a 3 dB point is 0.17 dB
down from passband response assuming a single pole roll-
off. As stated in the External Components section, both R
i
in conjunction with C
i, and Co with RL, create first order high-
pass filters. Thus to obtain the desired frequency low re-
sponse of 100 Hz within ±0.5 dB, both poles must be taken
into consideration. The combination of two single order filters
at the same frequency forms a second order response. This
results in a signal which is down 0.34 dB at five times away
from the single order filter 3 dB point. Thus, a frequency of
20 Hz is used in the following equations to ensure that the re-
sponse is better than 0.5 dB down at 100 Hz.
C
i ≥ 1/(2π *20k * 20 Hz) = 0.397 F; use 0.39 F.
C
o ≥ 1/(2π *8 * 20 Hz) = 995 F; use 1000 F.
The high frequency pole is determined by the product of the
desired high frequency pole, f
H, and the closed-loop gain, A
V
. With a closed-loop gain of 1.4 and f
H = 100 kHz, the result-
ing GBWP = 140 kHz which is much smaller than the
LM4882 GBWP of 12.5Mhz. This figure displays that if a de-
signer has a need to design an amplifier with a higher gain,
the LM4882 can still be used without running into bandwidth
limitations.
LM4882
www.national.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| LM4883SQ/NOPB | 0.4 W, 2 CHANNEL, AUDIO AMPLIFIER, QCC24 |
| LM4884MH/NOPB | 2.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20 |
| LM4888SQ/NOPB | 3 W, 2 CHANNEL, AUDIO AMPLIFIER, QCC24 |
| LM4889ITL/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 |
| LM4889ITLX/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM4883 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Dual 2.1W Audio Amplifier Plus Stereo Headphone |
| LM4883A E WAF | 制造商:Texas Instruments 功能描述: |
| LM4883SQ | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Dual 2.1W Audio Amplifier Plus Stereo Headphone |
| LM4883SQ/NOPB | 功能描述:IC AMP AUDIO PWR 3W STER 24LLP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:Boomer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| LM4883-SQ_BOM-001A | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Demo Board |
发布紧急采购，3分钟左右您将得到回复。