参数资料
型号: LM4891MX/NOPB
厂商: National Semiconductor
文件页数: 11/21页
文件大小: 0K
描述: IC AMP AUDIO PWR 1W MONO 8SOIC
标准包装: 2,500
系列: Boomer®
类型: AB 类
输出类型: 1-通道(单声道)
在某负载时最大输出功率 x 通道数量: 1W x 1 @ 8 欧姆
电源电压: 2.2 V ~ 5.5 V
特点: 消除爆音,关机,热保护
安装类型: 表面贴装
供应商设备封装: 8-SOIC
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
包装: 带卷 (TR)
配用: LM4891MBD-ND - BOARD EVALUATION LM4891M
其它名称: LM4891MX
OBSOLETE
SNAS122E – MAY 2001 – REVISED APRIL 2013
Table 1. Mono LM4891 Reference Design Boards Bill of Material for all 3 Demo Boards
Item
Part Number
Part Description
Qty
Ref Designator
1
551011208-001
LM4891 Mono Reference Design Board
1
10
482911183-001
LM4891 Audio AMP
1
U1
20
151911207-001
Tant Cap 1uF 16V 10
1
C1
21
151911207-002
Cer Cap 0.39uF 50V Z5U 20% 1210
1
C2
25
152911207-001
Tant Cap 1uF 16V 10
1
C3
30
472911207-001
Res 20K Ohm 1/10W 5
3
R1, R2, R3
35
210007039-002
Jumper Header Vertical Mount 2X1 0.100
2
J1, J2
PCB LAYOUT GUIDELINES
This section provides practical guidelines for mixed signal PCB layout that involves various digital/analog power
and ground traces. Designers should note that these are only "rule-of-thumb" recommendations and the actual
results will depend heavily on the final layout.
GENERAL MIXED SIGNAL LAYOUT RECOMMENDATION
POWER AND GROUND CIRCUITS
For 2 layer mixed signal design, it is important to isolate the digital power and ground trace paths from the
analog power and ground trace paths. Star trace routing techniques (bringing individual traces back to a central
point rather than daisy chaining traces together in a serial manner) can have a major impact on low level signal
performance. Star trace routing refers to using individual traces to feed power and ground to each circuit or even
device. This technique will take require a greater amount of design time but will not increase the final price of the
board. The only extra parts required may be some jumpers.
SINGLE-POINT POWER / GROUND CONNECTIONS
The analog power traces should be connected to the digital traces through a single point (link). A "Pi-filter" can
be helpful in minimizing high frequency noise coupling between the analog and digital sections. It is further
recommended to put digital and analog power traces over the corresponding digital and analog ground traces to
minimize noise coupling.
PLACEMENT OF DIGITAL AND ANALOG COMPONENTS
All digital components and high-speed digital signals traces should be located as far away as possible from
analog components and circuit traces.
AVOIDING TYPICAL DESIGN / LAYOUT PROBLEMS
Avoid ground loops or running digital and analog traces parallel to each other (side-by-side) on the same PCB
layer. When traces must cross over each other do it at 90 degrees. Running digital and analog traces at 90
degrees to each other from the top to the bottom side as much as possible will minimize capacitive noise
coupling and cross talk.
Copyright 2001–2013, Texas Instruments Incorporated
19
Product Folder Links: LM4891
相关PDF资料
PDF描述
LMH0002SQE/NOPB IC CABLE DVR SERIAL DGTL 16-LLP
LMH6734MQX/NOPB IC BUFFER TRPL SELECT 16-SSOP
LMK04010BISQ/NOPB IC CLOCK CONDITIONER W/PLL 48LLP
LMV393MUTAG IC OP AMP DUAL GP LV LV 8-UDFN
LMX339HASD+T IC COMPARATOR GP QUAD 14-SOIC
相关代理商/技术参数
参数描述
LM4892 制造商:NSC 制造商全称:National Semiconductor 功能描述:1 Watt Audio Power Amplifier with Headphone Sense
LM48920B WAF 制造商:Texas Instruments 功能描述:
LM4892B E WAF 制造商:Texas Instruments 功能描述:
LM4892BUPN E WAF 制造商:Texas Instruments 功能描述:
LM4892IBP 功能描述:IC AMP AUDIO PWR 1W MONO 8USMD RoHS:否 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:Boomer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机,2-通道(立体声) 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C,麦克风,静音,短路保护,音量控制 安装类型:表面贴装 供应商设备封装:25-WLP(2.09x2.09) 封装/外壳:25-WFBGA,WLCSP 包装:带卷 (TR)