- 您现在的位置：买卖IC网 > PDF目录30756 > LM4903MMX/NOPB (NATIONAL SEMICONDUCTOR CORP) 1.07 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 PDF资料下载
参数资料
| 型号： | LM4903MMX/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 1.07 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| 封装： | MSOP-8 |
| 文件页数： | 4/17页 |
| 文件大小： | 650K |
| 代理商： | LM4903MMX/NOPB |
Application Information (Continued)
from sources such as audio codecs. Please refer to the
section, Audio Power Amplifier Design, for a more com-
plete explanation of proper gain selection.
Besides gain, one of the major considerations is the closed-
loop bandwidth of the amplifier. To a large extent, the band-
width is dictated by the choice of external components
shown in Figure 1. The input coupling capacitor, C
i, forms a
first order high pass filter which limits low frequency re-
sponse. This value should be chosen based on needed
frequency response for a few distinct reasons.
Selection Of Input Capacitor Size
Large input capacitors are both expensive and space hungry
for portable designs. Clearly, a certain sized capacitor is
needed to couple in low frequencies without severe attenu-
ation. But in many cases the speakers used in portable
systems, whether internal or external, have little ability to
reproduce signals below 100Hz to 150Hz. Thus, using a
large input capacitor may not increase actual system perfor-
mance.
In addition to system cost and size, click and pop perfor-
mance is effected by the size of the input coupling capacitor,
C
i. A larger input coupling capacitor requires more charge to
reach its quiescent DC voltage (nominally 1/2 V
DD). This
charge comes from the output via the feedback and is apt to
create pops upon device enable. Thus, by minimizing the
capacitor size based on necessary low frequency response,
turn-on pops can be minimized.
Besides minimizing the input capacitor size, careful consid-
eration should be paid to the bypass capacitor value. Bypass
capacitor, C
B, is the most critical component to minimize
turn-on pops since it determines how fast the LM4903 turns
on. The slower the LM4903’s outputs ramp to their quiescent
DC voltage (nominally 1/2 V
DD), the smaller the turn-on pop.
Choosing C
B equal to 1.0F along with a small value of Ci (in
the range of 0.1F to 0.39F), should produce a virtually
clickless and popless shutdown function. While the device
will function properly, (no oscillations or motorboating), with
C
B equal to 0.1F, the device will be much more susceptible
to turn-on clicks and pops. Thus, a value of C
B equal to
1.0F is recommended in all but the most cost sensitive
designs.
AUDIO POWER AMPLIFIER DESIGN
A 1W/8
Audio Amplifier
Given:
Power Output
1 Wrms
Load Impedance
8
Input Level
1 Vrms
Input Impedance
20 k
Bandwidth
100 Hz–20 kHz ± 0.25 dB
A designer must first determine the minimum supply rail to
obtain the specified output power. By extrapolating from the
Output Power vs Supply Voltage graphs in the Typical Per-
formance Characteristics section, the supply rail can be
easily found.
5V is a standard voltage in most applications, it is chosen for
the supply rail. Extra supply voltage creates headroom that
allows the LM4903 to reproduce peaks in excess of 1W
without producing audible distortion. At this time, the de-
signer must make sure that the power supply choice along
with the output impedance does not violate the conditions
explained in the Power Dissipation section.
Once the power dissipation equations have been addressed,
the required differential gain can be determined from Equa-
tion 2.
(2)
R
f/Ri =AVD/2
From Equation 2, the minimum A
VD is 2.83; use AVD =3.
Since the desired input impedance was 20k
, and with a
A
VD impedance of 2, a ratio of 1.5:1 of Rf to Ri results in an
allocation of R
i = 20k
and R
f = 30k
. The final design step
is to address the bandwidth requirements which must be
stated as a pair of 3dB frequency points. Five times away
from a 3dB point is 0.17dB down from passband response
which is better than the required ±0.25dB specified.
f
L = 100Hz/5 = 20Hz
f
H = 20kHz*5= 100kHz
As stated in the External Components section, R
i in con-
junction with C
i create a highpass filter.
C
i
≥ 1/(2π*20k*20Hz) = 0.397F; use 0.39F
The high frequency pole is determined by the product of the
desired frequency pole, f
H, and the differential gain, AVD.
With a A
VD = 3 and fH = 100kHz, the resulting GBWP =
300kHz which is much smaller than the LM4903 GBWP of
2.5MHz. This figure displays that if a designer has a need to
design an amplifier with a higher differential gain, the
LM4903 can still be used without running into bandwidth
limitations.
The LM4903 is unity-gain stable and requires no external
components besides gain-setting resistors, an input coupling
capacitor, and proper supply bypassing in the typical appli-
cation. However, if a closed-loop differential gain of greater
than 10 is required, a feedback capacitor (C4) may be
needed as shown in Figure 2 to bandwidth limit the amplifier.
This feedback capacitor creates a low pass filter that elimi-
nates possible high frequency oscillations. Care should be
taken when calculating the -3dB frequency in that an incor-
rect combination of R
3
and C
4
will cause rolloff before
20kHz. A typical combination of feedback resistor and ca-
pacitor that will not produce audio band high frequency rolloff
is R
3 = 20k
and C
4 = 25pf. These components result in a
-3dB point of approximately 320kHz.
LM4903
www.national.com
12
相关PDF资料 |
PDF描述 |
|---|---|
| LM4905MM/NOPB | 1.07 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| LM4905LD/NOPB | 1.07 W, 1 CHANNEL, AUDIO AMPLIFIER, DSO10 |
| LM4905LQ/NOPB | 1.07 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC8 |
| LM4906LD/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, DSO10 |
| LM4906GR/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA12 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM4904 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:1 Watt Audio Power Amplifier |
| LM4904ITL | 制造商:Texas Instruments 功能描述:IC AMP AUDIO 1W SMD 4904 |
| LM4904ITL/NOPB | 功能描述:IC AMP AUDIO PWR 1.07W AB 8USMD RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:Boomer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| LM4905 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:1 Watt Audio Power Amplifier |
| LM4905LD | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
发布紧急采购，3分钟左右您将得到回复。