- 您现在的位置：买卖IC网 > PDF目录30756 > LM4910MMX/NOPB (NATIONAL SEMICONDUCTOR CORP) 0.035 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 PDF资料下载
参数资料
| 型号： | LM4910MMX/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 0.035 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| 封装： | MSOP-8 |
| 文件页数： | 11/22页 |
| 文件大小： | 828K |
| 代理商： | LM4910MMX/NOPB |
Application Information (Continued)
LM4910 Reference Design Boards
Bill of Materials
Part Description
Qty
Ref Designator
LM4910 Mono Reference Design Board
1
LM4910 Audio AMP
1
U1
Tantalum Cap 1F 16V 10
1
Cs
Ceramic Cap 0.39F 50V Z50 20
2
Ci
Resistor 20k
1/10W 5
4
Ri, Rf
Resistor 100k
1/10W 5
1
Rpu
Jumper Header Vertical Mount 2X1, 0.100
1
J1
PCB LAYOUT GUIDELINES
This section provides practical guidelines for mixed signal
PCB layout that involves various digital/analog power and
ground traces. Designers should note that these are only
"rule-of-thumb" recommendations and the actual results will
depend heavily on the final layout.
Minimization of THD
PCB trace impedance on the power, ground, and all output
traces should be minimized to achieve optimal THD perfor-
mance. Therefore, use PCB traces that are as wide as
possible for these connections. As the gain of the amplifier is
increased, the trace impedance will have an ever increasing
adverse affect on THD performance. At unity-gain (0dB) the
parasitic trace impedance effect on THD performance is
reduced but still a negative factor in the THD performance of
the LM4910 in a given application.
GENERAL MIXED SIGNAL LAYOUT
RECOMMENDATION
Power and Ground Circuits
For two layer mixed signal design, it is important to isolate
the digital power and ground trace paths from the analog
power and ground trace paths. Star trace routing techniques
(bringing individual traces back to a central point rather than
daisy chaining traces together in a serial manner) can
greatly enhance low level signal performance. Star trace
routing refers to using individual traces to feed power and
ground to each circuit or even device. This technique will
require a greater amount of design time but will not increase
the final price of the board. The only extra parts required may
be some jumpers.
Single-Point Power / Ground Connections
The analog power traces should be connected to the digital
traces through a single point (link). A "PI-filter" can be helpful
in minimizing high frequency noise coupling between the
analog and digital sections. Further, place digital and analog
power traces over the corresponding digital and analog
ground traces to minimize noise coupling.
Placement of Digital and Analog Components
All digital components and high-speed digital signal traces
should be located as far away as possible from analog
components and circuit traces.
Avoiding Typical Design / Layout Problems
Avoid ground loops or running digital and analog traces
parallel to each other (side-by-side) on the same PCB layer.
When traces must cross over each other do it at 90 degrees.
Running digital and analog traces at 90 degrees to each
other from the top to the bottom side as much as possible will
minimize capacitive noise coupling and cross talk.
LM4910
www.national.com
19
相关PDF资料 |
PDF描述 |
|---|---|
| LM4911LD/NOPB | 0.145 W, 2 CHANNEL, AUDIO AMPLIFIER, DSO10 |
| LM4913MH/NOPB | 0.09 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
| LM4914MH/NOPB | 0.085 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
| LM4915LQ/NOPB | 0.4 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC8 |
| LM4918LQ/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, QCC32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM4911 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Stereo 40mW Low Noise Headphone Amplifier with Selectable Capacitive Coupled or OCL Output |
| LM4911LD | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Stereo 40mW Low Noise Headphone Amplifier with Selectable Capacitive Coupled or OCL Output |
| LM4911LD/NOPB | 功能描述:IC AMP AUDIO PWR .145W AB 10LLP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:Boomer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| LM4911LDX | 功能描述:IC AMP AUDIO PWR .145W AB 10LLP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:Boomer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| LM4911MM | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。