- 您现在的位置：买卖IC网 > PDF目录30756 > LM4915LQ/NOPB (NATIONAL SEMICONDUCTOR CORP) 0.4 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC8 PDF资料下载
参数资料
| 型号： | LM4915LQ/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 0.4 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC8 |
| 封装： | LLP-8 |
| 文件页数： | 11/11页 |
| 文件大小： | 516K |
| 代理商： | LM4915LQ/NOPB |
Typical Performance Characteristics (Continued)
I
SD Distribution
V
DD =3V
200482F1
Application Information
DIFFERENTIAL AMPLIFIER EXPLANATION
The LM4915 is a pseudo-differential audio amplifier that
features a fixed gain of 6dB. Internally this is accomplished
by two separate sets of inverting amplifiers, each set to a
gain of 2. The LM4915 features precisely matched internal
gain-setting resistors set to R
i = 20k
and R
f = 40k
, thus
eliminating the need for external resistors and fixing the
differential gain at A
VD = 6dB.
A differential amplifier works in a manner where the differ-
ence between the two input signals is amplified. In most
applications, this would require input signals that are 180
out of phase with each other. The LM4915 works in a
pseudo-differential manner, so DC offset normally cancelled
by a fully differential amplifier needs to be blocked by input
coupling capacitors for the LM4915 to amplify the difference
between the inputs.
The LM4915 provides what is known as a ’bridged mode’
output (bridge-tied-load, BTL). This results in output signals
at Vo1 and Vo2 that are 180 out of phase with respect to
each other. Bridged mode operation is different from the
single-ended amplifier configuration that connects the load
between the amplifier output and ground. A bridged amplifier
design has distinct advantages over the single-ended con-
figuration: it provides differential drive to the load, thus dou-
bling maximum possible output swing for a specific supply
voltage. Four times the output power is possible compared
with a single-ended amplifier under the same conditions.
This increase in attainable output power assumes that the
amplifier is not current limited or clipped. A bridged configu-
ration, such as the one used in the LM4915, also creates a
second advantage over single-ended amplifiers. Since the
differential outputs, Vo1 and Vo2 , are biased at half-supply,
no net DC voltage exists across the load. BTL configuration
eliminates the output coupling capacitor required in single-
supply, single-ended amplifier configurations. If an output
coupling capacitor is not used in a single-ended output con-
figuration, the half-supply bias across the load would result
in both increased internal IC power dissipation as well as
permanent loudspeaker damage.
POWER DISSIPATION
Power dissipation is a major concern when designing a
successful amplifer, whether the amplifier is bridged or
single-ended. Equation 1 states the maximum power dissi-
pation point for a single-ended amplifier operating at a given
supply voltage and driving a specified output load.
P
DMAX =(VDD)
2 /(2
π2R
L)
Single-Ended
(1)
However, a direct consequence of the increased power de-
livered to the load by a bridge amplifier is an increase in
internal power dissipation versus a single-ended amplifier
operating at the same conditions.
P
DMAX = 4(VDD)
2 /(2
π2R
L)
Bridge Mode
(2)
Since the LM4915 has bridged outputs, the maximum inter-
nal power dissipation is 4 times that of a single-ended am-
plifier.
Even with this substantial increase in power dissipation, the
LM4915 does not require additional heatsinking under most
operating conditions and output loading. From Equation 2,
assuming a 5V power supply and an 16
load, the maximum
power dissipation point is 316mW. The maximum power
dissipation point obtained from Equation 2 must not be
greater than the power dissipation results from Equation 3:
P
DMAX =(TJMAX -TA)/
θ
JA
(3)
The LM4915’s
θ
JA in an LQB08A package is 140C/W. De-
pending on the ambient temperature, T
A , of the system
surroundings, Equation 3 can be used to find the maximum
internal power dissipation supported by the IC packaging. If
the result of Equation 2 is greater than that of Equation 3,
LM4915
www.national.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| LM4918LQ/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, QCC32 |
| LM4919MM/NOPB | 0.014 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
| LM4921ITLX/NOPB | SPECIALTY CONSUMER CIRCUIT, PBGA20 |
| LM4990ITL/NOPB | 2 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| LM4990ITLX/NOPB | 2 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM4915LQX | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LM4915LQX/NOPB | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LM4916 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:1.5V, Mono 85mW BTL Output, 14mW Stereo Headphone Audio Amplifier |
| LM4916LD | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LM4916LD/NOPB | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。