- 您现在的位置：买卖IC网 > PDF目录67756 > LM5025CCMTE (NATIONAL SEMICONDUCTOR CORP) SWITCHING CONTROLLER, 650 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | LM5025CCMTE |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 650 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | TSSOP-16 |
| 文件页数： | 9/16页 |
| 文件大小： | 369K |
| 代理商： | LM5025CCMTE |
Connection Diagram
30058916
16-Lead TSSOP
Ordering Information
Order Number
Package Type
NSC Package Drawing
Supplied As
LM5025CMTC
TSSOP-16
MTC-16
92 Units per anti-static tube
LM5025CMTCX
TSSOP-16
MTC-16
2500 Units on Tape and Reel
LM5025CCMTE
TSSOP-16
MTC-16
250 Units on Tape and Reel
Pin Descriptions
Pin
Name
Description
Application Information
1
V
IN
Source Input Voltage
Input to start-up regulator. Input range 13V to 90V, with
transient capability to 105V.
2
RAMP
Modulator ramp signal
An external RC circuit from Vin sets the ramp slope.
This pin is discharged at the conclusion of every cycle
by an internal FET, initiated by either the internal clock
or the V*Sec Clamp comparator.
3
CS1
Current sense input for cycle-by-cycle limiting
If CS1 exceeds 0.5V the outputs will go into Cycle-by-
Cycle current limit. CS1 is held low for 50ns after
OUT_A switches high providing leading edge blanking.
4
CS2
Current sense input for soft restart
If CS2 exceeds 0.5V the outputs will be disabled and a
softstart commenced. The soft-start capacitor will be
fully discharged and then released with a pull-up
current of 1A. After the first output pulse (when SS
=1V), the SS charge current will revert back to 90 A.
5
TIME
Output overlap/Deadtime control
An external resistor (R
SET) sets either the overlap time
or dead time for the active clamp output. An R
SET
resistor connected between TIME and GND produces
in-phase OUT_A and OUT_B pulses with overlap. An
R
SET resistor connected between TIME and REF
produces out-of-phase OUT_A and OUT_B pulses with
deadtime.
6
REF
Precision 5 volt reference output
Maximum output current: 10 mA Locally decouple with
a 0.1 F capacitor. Reference stays low until the V
CC
UV comparator is satisfied.
7
V
CC
Output from the internal high voltage start-up
regulator. The V
CC voltage is regulated to 7.6V.
If an auxiliary winding raises the voltage on this pin
above the regulation setpoint, the internal start-up
regulator will shutdown, reducing the IC power
dissipation.
www.national.com
2
LM5025C
相关PDF资料 |
PDF描述 |
|---|---|
| LM5025CSDX | SWITCHING CONTROLLER, DSO16 |
| LM5025CSD | SWITCHING CONTROLLER, DSO16 |
| LM5117PMHX | SWITCHING CONTROLLER, 530 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM5117PSQX | SWITCHING CONTROLLER, 530 kHz SWITCHING FREQ-MAX, QCC24 |
| LM5117PMHE | SWITCHING CONTROLLER, 530 kHz SWITCHING FREQ-MAX, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM5025CMTC | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Active Clamp Voltage Mode PWM Controller |
| LM5025CMTC/NOPB | 功能描述:电压模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| LM5025CMTCE/NOPB | 功能描述:电压模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| LM5025CMTCX | 制造商:Texas Instruments 功能描述:Voltage Mode PWM Controller 3A 16-Pin TSSOP T/R |
| LM5025CMTCX/NOPB | 功能描述:电压模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。