参数资料
型号: LM5046SQ
厂商: NATIONAL SEMICONDUCTOR CORP
元件分类: 稳压器
英文描述: SWITCHING CONTROLLER, 540 kHz SWITCHING FREQ-MAX, QCC28
封装: 5 X 5 MM, LLP-28
文件页数: 4/32页
文件大小: 888K
代理商: LM5046SQ
Functional Description
The LM5046 PWM controller contains all of the features nec-
essary to implement a Phase-Shifted Full-Bridge (PSFB)
topology power converter using either current mode or volt-
age mode control. This device is intended to operate on the
primary side of an isolated dc-dc converter with input voltage
up to 100V. This highly integrated controller-driver provides
dual 2A high and low side gate drivers for the four external
bridge MOSFETs plus control signals for secondary side syn-
chronous rectifiers. External resistors program the dead-time
to enable Zero-Volt Switching (ZVS) of the primary FETs.
Please refer to the Applications Information for details on the
operation of the PSFB topology. Intelligent startup of syn-
chronous rectifier allows turn-on of the power converter into
the pre-bias loads. Cycle-by-cycle current limit protects the
power components from load transients while hiccup mode
protection limits average power dissipation during extended
overload
conditions.
Additional
features
include
pro-
grammable soft-start, soft-start of the synchronous rectifiers,
and a 2 MHz capable oscillator with synchronization capability
and thermal shutdown.
High-Voltage Start-Up Regulator
The LM5046 contains an internal high voltage start-up regu-
lator that allows the input pin (VIN) to be connected directly
to the supply voltage over a wide range from 14V to 100V.
The input can withstand transients up to 105V. When the UV-
LO pin potential is greater than 0.4V, the VCC regulator is
enabled to charge an external capacitor connected to the
VCC pin. The VCC regulator provides power to the voltage
reference (REF) and the gate drivers (HO1/HO2 and LO1/
LO2). When the voltage on the VCC pin exceeds its Under
Voltage (UV) threshold, the internal voltage reference (REF)
reaches its regulation set point of 5V and the UVLO voltage
is greater than 1.25V, the soft-start capacitor is released and
normal operation begins. The regulator output at VCC is in-
ternally current limited. The value of the VCC capacitor de-
pends on the total system design, and its start-up character-
istics. The recommended range of values for the VCC
capacitor is 0.47
μF to 10F.
The internal power dissipation of the LM5046 can be reduced
by powering VCC from an external supply. The output voltage
of the VCC regulator is initially regulated to 9.5V. After the
synchronous rectifiers are engaged (which is approximately
when the output voltage in within regulation), the VCC voltage
is reduced to 7.7V. In typical applications, an auxiliary trans-
former winding is connected through a diode to the VCC pin.
This winding must raise the VCC voltage above 8V to shut off
the internal start-up regulator. Powering VCC from an auxil-
iary
winding
improves
efficiency
while
reducing
the
controller’s power dissipation. The VCC UV circuit will still
function in this mode, requiring that VCC never falls below its
UV threshold during the start-up sequence. The VCC regula-
tor series pass transistor includes a diode between VCC and
VIN that should not be forward biased in normal operation.
Therefore, the auxiliary VCC voltage should never exceed the
VIN voltage.
An external DC bias voltage can be used instead of the inter-
nal regulator by connecting the external bias voltage to both
the VCC and the VIN pins. This implementation is shown in
the Applications Information section. The external bias must
be greater than 10V and less than the VCC maximum voltage
rating of 14V.
Line Under-Voltage Detector
The LM5046 contains a dual level Under-Voltage Lockout
(UVLO) circuit. When the UVLO pin voltage is below 0.4V, the
controller is in a low current shutdown mode. When the UVLO
pin voltage is greater than 0.4V but less than 1.25V, the con-
troller is in standby mode. In standby mode the VCC and REF
bias regulators are active while the controller outputs are dis-
abled. When the VCC and REF outputs exceed their respec-
tive under-voltage thresholds and the UVLO pin voltage is
greater than 1.25V, the soft-start capacitor is released and the
normal operation begins. An external set-point voltage divider
from VIN to GND can be used to set the minimum operating
voltage of the converter. The divider must be designed such
that the voltage at the UVLO pin will be greater than 1.25V
when VIN enters the desired operating range. UVLO hystere-
sis is accomplished with an internal 20
μA current sink that is
switched on or off into the impedance of the set-point divider.
When the UVLO threshold is exceeded, the current sink is
deactivated to quickly raise the voltage at the UVLO pin.
When the UVLO pin voltage falls below the 1.25V threshold,
the current sink is enabled causing the voltage at the UVLO
pin to quickly fall. The hysteresis of the 0.4V shutdown com-
parator is internally fixed at 50mV.
The UVLO pin can also be used to implement various remote
enable / disable functions. Turning off the converter by forcing
the UVLO pin to standby condition (0.4V < UVLO < 1.25V)
provides a controlled soft-stop. Refer to the Soft Stop section
for more details.
Over Voltage Protection
An external voltage divider can be used to set either an over
voltage or an over temperature protection. During an OVP
condition, the SS and SSSR capacitors are discharged and
all the outputs are disabled. The divider must be designed
such that the voltage at the OVP pin is greater than 1.25V
when over voltage/temperature condition exists. Hysteresis is
accomplished with an internal 20
μA current source. When the
OVP pin voltage exceeds 1.25V, the 20
μA current source is
activated to quickly raise the voltage at the OVP pin. When
the OVP pin voltage falls below the 1.25V threshold, the cur-
rent source is deactivated causing the voltage at the OVP to
quickly fall. Refer to the Applications Information section for
more details.
Reference
The REF pin is the output of a 5V linear regulator that can be
used to bias an opto-coupler transistor and external house-
keeping circuits. The regulator output is internally current
limited to 15mA. The REF pin needs to be locally decoupled
with a ceramic capacitor, the recommended range of values
are from 0.1
μF to 10μF
Oscillator, Sync Input
The LM5046 oscillator frequency is set by a resistor connect-
ed between the RT pin and AGND. The RT resistor should be
located very close to the device. To set a desired oscillator
frequency (F
OSC), the necessary value of RT resistor can be
calculated from the following equation:
www.national.com
12
LM5046
相关PDF资料
PDF描述
LM5046MHX SWITCHING CONTROLLER, 540 kHz SWITCHING FREQ-MAX, PDSO28
LM5067SDX-2 2-CHANNEL POWER SUPPLY SUPPORT CKT, DSO10
LM5067SD-2 2-CHANNEL POWER SUPPLY SUPPORT CKT, DSO10
LM555H PULSE; RECTANGULAR, TIMER, MBCY8
LM555H/883B PULSE; RECTANGULAR, TIMER, MBCY8
相关代理商/技术参数
参数描述
LM5046SQ/NOPB 功能描述:电流型 PWM 控制器 Phase-Shifted Full- Bridge PWM Cntrlr RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
LM5046SQX 制造商:TI 制造商全称:Texas Instruments 功能描述:LM5046 Phase-Shifted Full-Bridge PWM Controller with Integrated MOSFET Drivers
LM5046SQX/NOPB 功能描述:IC PWM CTRLR FULL BRIDG 28LLP RoHS:是 类别:集成电路 (IC) >> PMIC - AC-DC 转换器,离线开关 系列:PowerWise® 标准包装:1 系列:FPS™ 输出隔离:隔离 频率范围:61kHz ~ 73kHz 输入电压:8 V ~ 26 V 输出电压:650V 功率(瓦特):12W 工作温度:-40°C ~ 115°C 封装/外壳:8-DIP(0.300",7.62mm) 供应商设备封装:8-MDIP 包装:Digi-Reel® 其它名称:FSL206MRBNFSDKR
LM505 制造商:LM TECHNOLOGIES 功能描述:ADAPTER BLUETOOTH NANO EDR 40M USB 制造商:LM TECHNOLOGIES 功能描述:BLUETOOTH ADAPTER, USB, BCM2045, EDR 制造商:LM TECHNOLOGIES 功能描述:BLUETOOTH ADAPTER, USB, BCM2045, 40M, EDR; Data Rate:2.166Mbps; Operating Temperature Min:-20C; Operating Temperature Max:75C; Operating Frequency Range:2.402GHz to 2.48GHz; Operating Temperature Range:-20C to +75C ;RoHS Compliant: Yes
LM5050-1 制造商:TI 制造商全称:Texas Instruments 功能描述:High Side OR-ing FET Controller