- 您现在的位置：买卖IC网 > PDF目录19386 > LM75BIMX-3+ (Maxim Integrated)IC TEMP SENSOR WATCHDOG 8SOIC PDF资料下载
参数资料
| 型号： | LM75BIMX-3+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 9/12页 |
| 文件大小： | 701K |
| 描述： | IC TEMP SENSOR WATCHDOG 8SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 功能： | 温度监视系统（传感器），监视器 |
| 传感器类型： | 内部 |
| 感应温度： | -55°C ~ 125°C |
| 精确度： | ±3°C（最小值） |
| 拓扑： | ADC（三角积分型），比较器，寄存器库 |
| 输出类型： | 2 线串行，I²C? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
Temperature Data Format
Temperature data is stored in the Temperature, T
OS
Set
Point, and T
HYST
Set Point registers. The temperature
data format is 9 bits, twos complement, and the register
is read out in 2 bytes: an upper byte and a lower byte.
Bits D15D7 contain the temperature data, with the LSB
representing 0.5癈 and the MSB representing the sign
bit (see Table 3). The MSB is transmitted first. The last 7
bits of the lower byte, bits D6D0, are dont cares.
Shutdown
Set bit D0 in the Configuration register to 1 to place the
LM75 in shutdown mode and reduce supply current to
4礎. In interrupt mode, entering shutdown resets the
OS output. While in shutdown, the I
2
C remains active
and T
OS
and T
HYST
limit registers along with the
Configuration register remain accessible to the master.
Fault Queue
The fault queue prevents OS false tripping in noisy
environments. The number of faults set in the queue (up
to 6) must occur to trip the OS output.
Comparator/Interrupt Mode
The events that trigger OS are identical between com-
parator and interrupt modes. In comparator mode, OS
is asserted when the temperature rises above the T
OS
value. OS is deasserted when the temperature drops
below the T
HYST
value. In interrupt mode, OS is assert-
ed when the temperature rises above the T
OS
value or
falls below the T
HYST
value. OS is deasserted only after
performing a read operation.
OS Output
The OS output is an open-drain output without an inter-
nal pullup. Connect a pullup resistor from OS to +V
S
.
Using larger resistance values reduces any tempera-
ture errors due to self heating from current entering OS.
OS Polarity
The OS polarity can be programmed for active-low or
active-high operation. In active-low operation, OS goes
low when triggered by a temperature event.
Internal Registers
The LM75s Pointer register selects between four data
registers (see Figure 6). At power-up, the pointer is set
to read the Temperature register at address 0x00. The
Pointer register latches the last location to which it was
set. All registers are read and write, except the
Temperature register, which is read only.
Write to the Configuration register by writing an address
byte, a data pointer byte, and a data byte. If 2 data
bytes are written, the second data byte overrides the
first. The T
OS
and T
HYST
registers require 1 address
byte, 1 pointer byte, and 2 data bytes. If only 1 data
byte is written, it is saved in bits D15D8 of the respec-
tive register. If more than 2 data bytes are written, only
the first 2 bytes are recognized while the remaining
bytes are ignored.
Read from the LM75 in one of two ways. If the location
latched in the Pointer register is set from the previous
read, the new read consists of an address byte, fol-
lowed by retrieving the corresponding number of data
bytes. If the Pointer register needs to be set to a new
address, perform a read operation by writing an
address byte, pointer byte, repeat start, and another
address byte.
An inadvertent 8-bit read from a 16-bit register, with the
D7 bit low, can cause the device to stop in a state
where the SDA line is held low. Ordinarily, this would
prevent any further bus communication until the master
sends nine additional clock cycles or SDA goes high.
At that time, a stop condition resets the device. If the
additional clock cycles are not generated by the mas-
ter, the LM75 bus resets and unlocks after the bus time-
out period has elapsed.
Digital Temperature Sensor and Thermal
Watchdog with 2-Wire Interface
_______________________________________________________________________________________ 9
SMBus is a trademark of Intel Corp.
Figure 6. Block Diagram
LM75
+V
S
A2/RESET
A1
A0
SDA
SCL
OS
SMBus"
INTERFACE
BLOCK
POINTER REGISTER
(SELECTS REGISTER
FOR COMMUNICATION)
DATA
ADDRESS
REGISTER SELECT
GND
TEMPERATURE
(READ ONLY)
POINTER = 0000 0000
T
OS
SET POINT
(READ/WRITE)
POINTER = 0000 0011
T
HYST
SET POINT
(READ/WRITE)
POINTER = 0000 0010
CONFIGURATION
(READ/WRITE)
POINTER = 0000 0001
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2N4-CY-F3 | CONVERTER MOD DC/DC 48V 50W |
| MAX31722MUA+ | IC THERMOMETER/STAT SPI-3W 8UMAX |
| GEM06DRYS | CONN EDGECARD 12POS DIP .156 SLD |
| VI-2N3-CY-F1 | CONVERTER MOD DC/DC 24V 50W |
| MAX6514UKP115+T | IC TEMP SWITCH SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM75BIMX-3 NOPB | 制造商:Texas Instruments 功能描述:Temp Sensor Digital Serial (2-Wire, I2C) 8-Pin SOIC T/R |
| LM75BIMX-3/NOPB | 功能描述:板上安装温度传感器 DIGITAL TEMP SENSOR RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| LM75BIMX-3+ | 功能描述:板上安装温度传感器 2-Wire Digital Temp Snsr & Thrml Wtchdog RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| LM75BIMX5 | 制造商:National Semiconductor 功能描述:Temp Sensor Digital Serial (2-Wire, I2C) 8-Pin SOIC N T/R |
| LM75BIMX-5 | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。