- 您现在的位置：买卖IC网 > PDF目录358873 > LM75DM-33R2 (ON SEMICONDUCTOR) 2-Wire Serial Temperature Sensor and Monitor PDF资料下载
参数资料
| 型号： | LM75DM-33R2 |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | 温度/湿度传感器 |
| 英文描述： | 2-Wire Serial Temperature Sensor and Monitor |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 3Cel, SQUARE, SURFACE MOUNT |
| 封装： | PLASTIC, MICROPAK-8 |
| 文件页数： | 4/12页 |
| 文件大小： | 150K |
| 代理商： | LM75DM-33R2 |
LM75
http://onsemi.com
4
DETAILED OPERATING DESCRIPTION
A typical LM75 hardware connection is shown in Figure 1.
Figure 1. Typical Application
+VDD
A0
A1
A2
SDA
SCL
TCN75
CBypass
7
6
5
1
2
3
8
Address
(Set as Desired)
Interface
4
0.1 F Recommended
Unless Device is
Mounted Close to CPU
Two Wire
INT/CMPTR
Serial Data (SDA)
Bidirectional. Serial data is transferred in both directions
using this pin.
Serial Clock (SCL)
Input. Clocks data into and out of the LM75.
INT/CMPTR
Open Collector, Programmable Polarity. In Comparator
Mode, unconditionally driven active any time temperature
exceeds the value programmed into the T
SET
register.
INT/CMPTR will become inactive when temperature
subsequently falls below the T
HYST
setting. (See
Register Set
and
Programmer’s
Model.
)
INT/CMPTR is made active by TEMP exceeding T
SET
; it is
unconditionally reset to its inactive state by reading any
register via the 2–wire bus. If and when temperature falls
below T
HYST
, INT/CMPTR is again driven active. Reading
any register will clear the T
HYST
interrupt. In Interrupt Mode,
the INT/CMPTR output is unconditionally reset upon
entering Shutdown Mode. If programmed as an active–low
output, it can be wire–ORed with any number of other open
collector devices. Most systems will require a pull–up
resistor for this configuration.
Note that current sourced from the pull–up resistor causes
power dissipation and may cause internal heating of the
LM75. To avoid affecting the accuracy of ambient
temperature readings, the pull–up resistor should be made as
large as possible. INT/CMPTR’s output polarity may be
programmed by writing to the INT/CMPTR POLARITY bit
in the CONFIG register. The default is active low.
In
Interrupt
Mode,
Address (A2, A1, A0)
Inputs. Sets the three least significant bits of the LM75
8–bit address. A match between the LM75’s address and the
address specified in the serial bit stream must be made to
initiate
communication
with
protocol–compatible devices with other addresses may
share the same 2–wire bus.
the
LM75.
Many
Slave Address
The four most significant bits of the Address Byte (A6,
A5, A4, A3) are fixed to 1001[B]. The states of A2, A1 and
A0 in the serial bit stream must match the states of the A2,
A1 and A0 address inputs for the LM75 to respond with an
Acknowledge (indicating the LM75 is on the bus and ready
to accept data). The Slave Address is represented by:
LM75 Slave Address
1
0
0
1
A2
A1
A0
MSB
LSB
Comparator/Interrupt Modes
INT/CMPTR behaves differently depending on whether
the LM75 is in Comparator Mode or Interrupt Mode.
Comparator Mode is designed for simple thermostatic
operation. INT/CMPTR will go active anytime TEMP
exceeds T
SET
. When in Comparator Mode, INT/CMPTR
will remain active until TEMP falls below T
HYST
, whereupon
it will reset to its inactive state. The state of INT/CMPTR is
maintained in shutdown mode when the LM75 is in
comparator mode. In Interrupt Mode, INT/CMPTR will
remain active indefinitely, even if TEMP falls below T
HYST
,
until any register is read via the 2–wire bus. Interrupt Mode
is better suited to interrupt driven microprocessor–based
systems. The INT/CMPTR output may be wire–OR’ed with
other interrupt sources in such systems. Note that a pull–up
resistor is necessary on this pin since it is an open–drain
output. Entering Shutdown Mode will unconditionally reset
INT/CMPTR when in Interrupt Mode.
SHUTDOWN MODE
When the appropriate bit is set in the configuration
register (CONFIG) the LM75 enters its low–power
shutdown mode (I
DD
= 1
μ
A, typical) and the
temperature–to–digital conversion process is halted. The
LM75’s bus interface remains active and TEMP, T
SET
, and
T
HYST
may be read from and written to. Transitions on SDA
or SCL due to external bus activity may increase the standby
power consumption. If the LM75 is in Interrupt Mode, the
state of INT/CMPTR will be RESET upon entering
shutdown mode.
Fault Queue
To lessen the probability of spurious activation of
INT/CMPTR the LM75 may be programmed to filter out
transient events. This is done by programming the desired
value into the Fault Queue. Logic inside the LM75 will
prevent the device from triggering INT/CMPTR unless the
programmed number of sequential temperature–to–digital
conversions yield the same qualitative result. In other words,
the value reported in TEMP must remain above T
SET
or
below T
HYST
for the consecutive number of cycles
相关PDF资料 |
PDF描述 |
|---|---|
| LM77000 | Power Operational Amplifiers |
| LM77000CP | Power Operational Amplifiers |
| LM77CIMM-5 | 9-Bit Sign Digital Temperature Sensor and Thermal Window Comparator with Two-Wire Interface |
| LM7800C | Series 3-Terminal Positive Regulators |
| LM7805 | 1.5A Positive Voltage Regulator |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM75DM-50R2 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| LM76 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:【0.5∑C, 【1∑C, 12-Bit Sign Digital Temperature Sensor and Thermal Window Comparator with Two-Wire Interface |
| LM76 WAF | 制造商:Texas Instruments 功能描述: |
| LM760 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:High Speed Differential Comparator |
| LM760 WAF | 制造商:Texas Instruments 功能描述: |
发布紧急采购，3分钟左右您将得到回复。