- 您现在的位置：买卖IC网 > PDF目录69005 > LM8801XUX-1.82 (NATIONAL SEMICONDUCTOR CORP) 1.3 A SWITCHING REGULATOR, 6400 kHz SWITCHING FREQ-MAX, BGA6 PDF资料下载
参数资料
| 型号： | LM8801XUX-1.82 |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 1.3 A SWITCHING REGULATOR, 6400 kHz SWITCHING FREQ-MAX, BGA6 |
| 封装： | 1.065 X 1.265 MM, 0.25 MM HEIGHT, 0.40 MM PITCH, MICRO, SMD-6 |
| 文件页数： | 4/18页 |
| 文件大小： | 1019K |
| 代理商： | LM8801XUX-1.82 |
Application Information
INDUCTOR SELECTION
There are two main considerations when choosing an induc-
tor; the inductor should not saturate, and the inductor current
ripple is small enough to achieve the desired output voltage
ripple. Different manufacturers follow different saturation cur-
rent rating specifications, so attention must be given to de-
tails. Saturation current ratings are typically specified at 25°C
so ratings at maximum ambient temperature of application
should be requested from manufacturer.
Minimum value of inductance to guarantee good perfor-
mance is 0.3 H at (I
LIM typ.) bias current over the ambient
temp range.
Shielded inductors radiate less noise and should be pre-
ferred. There are two methods to choose the inductor satu-
ration current rating.
Method 1:
The saturation current should be greater than the sum of the
maximum load current and the worst case average to peak
inductor current. This can be written as:
I
RIPPLE: average to peak inductor current
I
OUTMAX: maximum load current (600 mA)
V
IN: maximum input voltage in application
L: minimum inductor value including worst case tolerances
(30% drop can be considered for method 1)
f: minimum switching frequency (5.4 MHz)
V
OUT: output voltage
Method 2:
A more conservative and recommended approach is to
choose an inductor that can handle the maximum current limit
of 1300 mA.
The inductor's resistance should be less than around 0.1
for
good efficiency. Table 1 lists suggested inductors and sup-
pliers.
INPUT CAPACITOR SELECTION
A ceramic input capacitor of 2.2 F, 6.3V is sufficient for most
applications. Place the input capacitor as close as possible to
the V
IN pin of the device. A larger value or higher voltage rat-
ing may be used to improve input voltage filtering. Use X7R
or X5R types; do not use Y5V. DC bias characteristics of ce-
ramic capacitors must be considered when selecting case
sizes like 0402 and 0603.
The input filter capacitor supplies current to the top switch of
the LM8801 in the first half of each cycle and reduces voltage
ripple imposed on the input power source. A ceramic
capacitor's low ESR provides the best noise filtering of the
input voltage spikes due to this rapidly changing current. Se-
lect an input filter capacitor with sufficient ripple current rating.
The input current ripple can be calculated as:
The worst case is when V
IN = 2 x VOUT.
TABLE 1. Suggested Inductors and Suppliers
Model
Vendor
Dimensions LxWxH (mm)
MIPSZ2012D0R5
FDK
2.0 x 1.2 x 1.0
LQM21PNR54MG0D
Murata
2.0 x 1.2 x 0.9
HSLI-201208AG-R47
Hitachi Metals
2.0 x 1.2 x 0.8
OUTPUT CAPACITOR SELECTION
Use a 4.7
μF, 6.3V ceramic capacitor, X7R or X5R types; do
not use Y5V. DC bias characteristics of ceramic capacitors
must be considered when selecting case sizes 0402 and
0603. DC bias characteristics vary from manufacturer to man-
ufacturer, and DC bias curves should be requested from them
as part of the capacitor selection process. Minimum output
capacitance to guarantee good performance is 2.2 F (for
4.7 F capacitor) at 1.8V DC bias including tolerances and
over ambient temp range.
The output filter capacitor smooths out current flow from the
inductor to the load, helps maintain a steady output voltage
during transient load changes and reduces output voltage
ripple. These capacitors must be selected with sufficient ca-
pacitance and sufficiently low ESR to perform these functions.
The output voltage ripple is caused by the charging and dis-
charging of the output capacitor and also due to its R
ESR and
can be calculated as:
Voltage peak-to-peak ripple due to capacitance =
Voltage peak-to-peak ripple due to ESR =
V
PP-ESR = (2 * IRIPPLE) * RESR
Because these two components are out of phase, the rms
value can be used to get an approximate value of peak-to-
peak ripple.
Voltage peak-to-peak ripple, root mean squared =
Note that the output voltage ripple is dependent on the current
ripple and the equivalent series resistance of the output ca-
pacitor (R
ESR). The RESR is frequency dependent (as well as
temperature dependent); make sure the value used for cal-
culations is at the switching frequency of the part.
Table 2 lists suggested capacitors and suppliers.
www.national.com
12
LM8801
相关PDF资料 |
PDF描述 |
|---|---|
| LM8805TLX/NOPB | POWER SUPPLY MANAGEMENT CKT, PBGA9 |
| LM8805TLE/NOPB | POWER SUPPLY MANAGEMENT CKT, PBGA9 |
| LM96080CIMTX-NOPB | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO24 |
| LM96080CIMT-NOPB | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO24 |
| LMX1602TMX/NOPB | PLL FREQUENCY SYNTHESIZER, 1100 MHz, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM8802 | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| LM8802G | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| LM8802S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| LM8804 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| LM8804G | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
发布紧急采购，3分钟左右您将得到回复。