- 您现在的位置：买卖IC网 > PDF目录3606 > LMH6643MM/NOPB (National Semiconductor)IC AMP 130MHZ R-R OPUT 8-MSOP PDF资料下载
参数资料
| 型号： | LMH6643MM/NOPB |
| 厂商： | National Semiconductor |
| 文件页数： | 10/33页 |
| 文件大小： | 0K |
| 描述： | IC AMP 130MHZ R-R OPUT 8-MSOP |
| 产品培训模块： | High Speed Amplifiers for Video Applications - Part 1 High Speed Amplifiers for Video Applications - Part 2 High Speed Amplifiers for Video Applications - Part 3 |
| 标准包装： | 1 |
| 系列： | PowerWise® |
| 放大器类型： | 电压反馈 |
| 电路数： | 2 |
| 输出类型： | 满摆幅 |
| 转换速率： | 135 V/µs |
| -3db带宽： | 130MHz |
| 电流 - 输入偏压： | 1.6µA |
| 电压 - 输入偏移： | 1000µV |
| 电流 - 电源： | 2.7mA |
| 电流 - 输出 / 通道： | 75mA |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 12.8 V，±1.35 V ~ 6.4 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 1270 (CN2011-ZH PDF) |
| 其它名称： | LMH6643MMDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
IN+
IN-
R
V-
V+
V-
VIN (1 V/DIV)
VOUT (2 V/DIV)
VS=±5V, VIN=5VPP
AV=+5, RF=RL=2k
2 V/DIV
100 ns/DIV
SNOS966P – MAY 2001 – REVISED MARCH 2013
Figure 61. Overload Recovery Waveform
INPUT AND OUTPUT TOPOLOGY
All input / output pins are protected against excessive voltages by ESD diodes connected to V+ and V-rails (see
Figure 62). These diodes start conducting when the input / output pin voltage approaches 1Vbe beyond V
+ or V-
to protect against over voltage. These diodes are normally reverse biased. Further protection of the inputs is
provided by the two resistors (R in Figure 62), in conjunction with the string of anti-parallel diodes connected
between both bases of the input stage. The combination of these resistors and diodes reduces excessive
differential input voltages approaching 2Vbe. The most common situation when this occurs is when the device is
used as a comparator (or with little or no feedback) and the device inputs no longer follow each other. In such a
case, the diodes may conduct. As a consequence, input current increases and the differential input voltage is
clamped. It is important to make sure that the subsequent current flow through the device input pins does not
violate the Absolute Maximum Ratings of the device. To limit the current through this protection circuit, extra
series resistors can be placed. Together with the built-in series resistors of several hundred ohms, these external
resistors can limit the input current to a safe number (i.e. < 10mA). Be aware that these input series resistors
may impact the switching speed of the device and could slow down the device.
Figure 62. Input Equivalent Circuit
SINGLE SUPPLY, LOW POWER PHOTODIODE AMPLIFIER
The circuit shown in Figure 63 is used to amplify the current from a photodiode into a voltage output. In this
circuit, the emphasis is on achieving high bandwidth and the transimpedance gain setting is kept relatively low.
Because of its high slew rate limit and high speed, the LMH664X family lends itself well to such an application.
This circuit achieves approximately 1V/mA of transimpedance gain and capable of handling up to 1mApp from the
photodiode. Q1, in a common base configuration, isolates the high capacitance of the photodiode (Cd) from the
Op Amp input in order to maximize speed. Input is AC coupled through C1 to ease biasing and allow single
supply operation. With 5V single supply, the device input/output is shifted to near half supply using a voltage
divider from VCC. Note that Q1 collector does not have any voltage swing and the Miller effect is minimized. D1,
tied to Q1 base, is for temperature compensation of Q1’s bias point. Q1 collector current was set to be large
enough to handle the peak-to-peak photodiode excitation and not too large to shift the U1 output too far from
mid-supply.
18
Copyright 2001–2013, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| RMCF0603FT14K7 | RES 14.7K OHM 1/10W 1% 0603 SMD |
| RMCF0603FT13K0 | RES 13K OHM 1/10W 1% 0603 SMD |
| RMCF0603FT11K0 | RES 11K OHM 1/10W 1% 0603 SMD |
| RMCF0603FT6K98 | RES 6.98K OHM 1/10W 1% 0603 SMD |
| RMCF0603FT6K19 | RES 6.19K OHM 1/10W 1% 0603 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LMH6643MMX | 功能描述:运算放大器 - 运放 RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| LMH6643MMX/NOPB | 功能描述:运算放大器 - 运放 RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| LMH6643MMX/S5001341 | 制造商:Texas Instruments 功能描述: |
| LMH6643MMX/S7002247 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| LMH6643QMM | 制造商:TI 制造商全称:Texas Instruments 功能描述:Low Power, 130MHz, 75mA Rail-to-Rail Output Amplifiers |
发布紧急采购，3分钟左右您将得到回复。