- 您现在的位置：买卖IC网 > PDF目录39250 > LMP91000SDX (NATIONAL SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, PDSO14 PDF资料下载
参数资料
| 型号： | LMP91000SDX |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO14 |
| 封装： | LLP-14 |
| 文件页数： | 8/24页 |
| 文件大小： | 696K |
| 代理商： | LMP91000SDX |
MODECN -- Mode Control Register (address 0x12)
The Parameters in the Mode register allow the configuration of the Operation Mode of the LMP91000.
Bit
Name
Function
7
FET_SHORT
Shorting FET feature
0 Disabled (default)
1 Enabled
[6:3]
RESERVED
[2:0]
OP_MODE
Mode of Operation selection
000 Deep Sleep (default)
001 2-lead ground referred galvanic cell
010 Standby
011 3-lead amperometric cell
110 Temperature measurement (TIA OFF)
111 Temperature measurement (TIA ON)
When the LMP91000 is in Temperature measurement (TIA ON) mode, the output of the temperature sensor is present at the VOUT
pin, while the output of the potentiostat circuit is available at pin C2.
GAS SENSOR INTERFACE
The LMP91000 supports both 3-lead and 2-lead gas sensors.
Most of the toxic gas sensors are amperometric cells with 3
leads (Counter, Worker and Reference). These leads should
be connected to the LMP91000 in the potentiostat topology.
The 2-lead gas sensor (known as galvanic cell) should be
connected as simple buffer either referred to the ground of the
system or referred to a reference voltage. The LMP91000
support both connections for 2-lead gas sensor.
3-lead Amperometric Cell In Potentiostat Configuration
Most of the amperometric cell have 3 leads (Counter, Refer-
ence and Working electrodes). The interface of the 3-lead gas
sensor to the LMP91000 is straightforward, the leads of the
gas sensor need to be connected to the namesake pins of the
LMP91000.
The LMP91000 is then configured in 3-lead amperometric cell
mode; in this configuration the Control Amplifier (A1) is ON
and provides the internal zero voltage and bias in case of bi-
ased gas sensor. The transimpedance amplifier (TIA) is ON,
it converts the current generated by the gas sensor in a volt-
age, according to the transimpedance gain:
Gain=R
TIA
If different gains are required, an external resistor can be
connected between the pins C1 and C2. In this case the in-
ternal feedback resistor should be programmed to “external”.
The R
Load together with the output capacitance of the gas
sensor acts as a low pass filter.
www.national.com
16
LMP91000
相关PDF资料 |
PDF描述 |
|---|---|
| LMS33460MGX/NOPB | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| LMS33460MWC | 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC |
| LMS500-5CC | LOW PASS FILTER |
| LMS500-5SS | LOW PASS FILTER |
| LMTLF12UA102WR04 | SINGLE PHASE EMI FILTER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LMP91000SDX/NOPB | 功能描述:空气质量传感器 RoHS:否 制造商:GE M&C / Telaire 类型:CO2 Module 检测灵敏度: 工作电源电压:5 V 最大工作温度:+ 50 C 最小工作温度:0 C |
| LMP91002 | 制造商:TI 制造商全称:Texas Instruments 功能描述:Sensor AFE System: Configurable AFE Potentiostat |
| LMP91002SD | 制造商:TI 制造商全称:Texas Instruments 功能描述:Sensor AFE System: Configurable AFE Potentiostat |
| LMP91002SD/NOPB | 制造商:Texas Instruments 功能描述:CONFIGURABLE AFE POTENTIOSTAT FOR LOW-PO - Tape and Reel 制造商:Texas Instruments 功能描述:IC AFE INTERFACE 14WSON 制造商:Texas Instruments 功能描述:Configurable AFE Potentiostat for Low-Po |
| LMP91002SDE | 制造商:TI 制造商全称:Texas Instruments 功能描述:Sensor AFE System: Configurable AFE Potentiostat |
发布紧急采购，3分钟左右您将得到回复。