- 您现在的位置：买卖IC网 > PDF目录358884 > LMV301MGX (NATIONAL SEMICONDUCTOR CORP) Low Input Bias Current, 1.8V Op Amp w/ Rail-to-Rail Output PDF资料下载
参数资料
| 型号： | LMV301MGX |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 运算放大器 |
| 英文描述： | Low Input Bias Current, 1.8V Op Amp w/ Rail-to-Rail Output |
| 中文描述： | OP-AMP, 9000 uV OFFSET-MAX, 1 MHz BAND WIDTH, PDSO5 |
| 封装： | SC-70, 5 PIN |
| 文件页数： | 13/19页 |
| 文件大小： | 624K |
| 代理商： | LMV301MGX |
Application Hints
(Continued)
Capacitive Load Tolerance
Like many other op amps, the LMV301 may oscillate when
its applied load appears capacitive. The threshold of
oscillation varies both with load and circuit gain. The
configuration most sensitive to oscillation is a unity gain
follower. The load capacitance interacts with the op amp’s
output resistance to create an additional pole. If this pole
frequency is sufficiently low, it will degrade the op amp’s
phase margin so that the amplifier is no longer stable. As
shown in Figure 2 the addition of a small resistor (50
to
100
) in series with the op amp’s output, and a capacitor
(5pF to 10pF) from inverting input to output pins, returns the
phase margin to a safe value without interfering with lower
frequency
circuit
operation.
capacitance can be tolerated without oscillation. Note that in
all cases, the output will ring heavily when the load
capacitance is near the threshold for oscillation.
Thus,
larger
values
of
Capacitive load driving capability is enhanced by using a pull
up resistor to V
+
(Figure 3). Typically a pull up resistor
conducting
500μA or
more
capacitive load responses. The value of the pull up resistor
must be determined based on the current sinking capability
of the amplifier with respect to the desired output swing.
Open loop gain of the amplifier can also be affected by the
pull up resistor.
will
significantly
improve
PRINTED-CIRCUIT-BOARD LAYOUT
FOR HIGH-IMPEDANCE WORK
It is generally recognized that any circuit which must operate
with less than 100pA of leakage current requires special
layout of the PC board. When one wishes to take advantage
of the low bias current of the LMV301, typically less than
0.182pA, it is essential to have an excellent layout.
Fortunately, the techniques for obtaining low leakages are
quite simple. First, the user must not ignore the surface
leakage of the PC board, even though it may sometimes
appear acceptable low, because under conditions of the high
humidity or dust or contamination, the surface leakage will
be appreciable. To minimized the effect of any surface
leakage, lay out a ring of foil completely surrounding the
LMV301’s inputs and the terminals of capacitors, diodes,
conductors, resistors, relay terminals, etc. connected to the
op amp’s inputs. See Figure 4 To have a significant effect,
guard rings should be placed on both the top and bottom of
the PC board. The PC foil must then be connected to a
voltage which is at the same voltage as the amplifier inputs,
since no leakage current can flow between two points at the
same potential. For example, a PC board trace-to-pad
resistance of 10
12
, which is normally considered a very
large resistance, could leak 5pA if the trace were a 5V bus
adjacent to the pad of an input. This would cause a 100
times degradation from the LMV301’s actual performance.
However, if a guard ring is held within 5mV of the inputs, then
even a resistance of 10
11
would cause only 0.05pA of
leakage current, or perhaps a minor (2:1) degradation of the
amplifier performance. See Figure 5a, Figure 5b, Figure 5c
for typical connections of guard rings for standard op amp
configurations. If both inputs are active and at high
impedance, the guard can be tied to ground and still provide
some protection; see Figure 5d.
20019305
FIGURE 2. Rx, Cx Improve Capacitive Load Tolerance
20019323
FIGURE 3. Compensating for Large Capacitive Loads
with a Pull Up Resistor
20019377
FIGURE 4. Example, using the LMV301,
of Guard Ring in P.C. Board Layout
L
www.national.com
13
相关PDF资料 |
PDF描述 |
|---|---|
| LMV324D | LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS |
| LMV339D | GENERAL-PURPOSE LOW-VOLTAGE COMPARATORS |
| LMV339MX | General Purpose, Low Voltage, TinyPack Comparators |
| LMV339MTX | General Purpose, Low Voltage, TinyPack Comparators |
| LMV339MT | General Purpose, Low Voltage, TinyPack Comparators |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LMV301MGX/NOPB | 功能描述:运算放大器 - 运放 RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| LMV301SQ3T2G | 功能描述:运算放大器 - 运放 LV SNGL OP AMP SC70 RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| LMV321 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:General Purpose, Low Voltage, Rail-to-Rail Output Amplifiers |
| LMV321_07 | 制造商:TI 制造商全称:Texas Instruments 功能描述:LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS |
| LMV321_08 | 制造商:TI 制造商全称:Texas Instruments 功能描述:LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS |
发布紧急采购，3分钟左右您将得到回复。