- 您现在的位置：买卖IC网 > PDF目录80264 > LMZ12002EXTTZE-ADJ (NATIONAL SEMICONDUCTOR CORP) SWITCHING REGULATOR, PSSO7 PDF资料下载
参数资料
| 型号： | LMZ12002EXTTZE-ADJ |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, PSSO7 |
| 封装： | 10.16 X 13.77 MM, 4.57 MM HEIGHT, ROHS COMPLIANT, TO-PMOD-7 |
| 文件页数： | 5/20页 |
| 文件大小： | 3951K |
| 代理商： | LMZ12002EXTTZE-ADJ |
The inverse relationship of t
ON and VIN gives a nearly constant
switching frequency as VIN is varied. R
ON should be selected
such that the on-time at maximum V
IN is greater than 150 ns.
The on-timer has a limiter to ensure a minimum of 150 ns for
t
ON. This limits the maximum operating frequency, which is
governed by the following equation:
f
SW(MAX) = VO / (VIN(MAX) * 150 nsec) (13)
This equation can be used to select R
ON if a certain operating
frequency is desired so long as the minimum on-time of 150
ns is observed. The limit for R
ON can be calculated as follows:
R
ON ≥ VIN(MAX) * 150 nsec / (1.3 * 10
-10
) (14)
If R
ON calculated in (11) is less than the minimum value de-
termined in (14) a lower frequency should be selected. Alter-
natively, V
IN(MAX) can also be limited in order to keep the
frequency unchanged.
Additionally note, the minimum off-time of 260 ns limits the
maximum duty ratio. Larger R
ON (lower FSW) should be se-
lected in any application requiring large duty ratio.
Discontinuous Conduction and Continuous Conduction
Modes
At light load the regulator will operate in discontinuous con-
duction mode (DCM). With load currents above the critical
conduction point, it will operate in continuous conduction
mode (CCM). When operating in DCM the switching cycle
begins at zero amps inductor current; increases up to a peak
value, and then recedes back to zero before the end of the
off-time. Note that during the period of time that inductor cur-
rent is zero, all load current is supplied by the output capacitor.
The next on-time period starts when the voltage on the at the
FB pin falls below the internal reference. The switching fre-
quency is lower in DCM and varies more with load current as
compared to CCM. Conversion efficiency in DCM is main-
tained since conduction and switching losses are reduced
with the smaller load and lower switching frequency. Operat-
ing frequency in DCM can be calculated as follows:
f
SW(DCM)VO*(VIN-1)*10 μH*1.18*10
20
*I
O/(VIN–VO)*RON
2 (15)
In CCM, current flows through the inductor through the entire
switching cycle and never falls to zero during the off-time. The
switching frequency remains relatively constant with load cur-
rent and line voltage variations. The CCM operating frequen-
cy can be calculated using equation 7 above.
Following is a comparison pair of waveforms of the showing
both CCM (upper) and DCM operating modes.
CCM and DCM Operating Modes
V
IN = 12V, VO = 3.3V, IO = 2A/0.26A 2 μsec/div
30117412
The approximate formula for determining the DCM/CCM
boundary is as follows:
I
DCBVO*(VIN–VO)/(2*10 μH*fSW(CCM)*VIN) (16)
Following is a typical waveform showing the boundary condi-
tion.
Transition Mode Operation
V
IN = 12V, VO = 3.3V, IO = 0.29A 2 μsec/div
30117414
The inductor internal to the module is 10
μH. This value was
chosen as a good balance between low and high input voltage
applications. The main parameter affected by the inductor is
the amplitude of the inductor ripple current (I
LR). ILR can be
calculated with:
I
LR P-P=VO*(VIN- VO)/(10H*fSW*VIN) (17)
Where V
IN is the maximum input voltage and fSW is deter-
mined from equation 10.
If the output current I
O is determined by assuming that IO =
I
L, the higher and lower peak of ILR can be determined. Be
aware that the lower peak of I
LR must be positive if CCM op-
eration is required.
POWER DISSIPATION AND BOARD THERMAL
REQUIREMENTS
For the design case of V
IN = 12V, VO = 3.3V, IO = 2A, TAMB
(MAX) = 85°C , and TJUNCTION = 125°C, the device must see a
thermal resistance from case to ambient of:
θ
CA< (TJ-MAX — TAMB(MAX)) / PIC-LOSS - θJC (18)
Given the typical thermal resistance from junction to case to
be 1.9 °C/W .Use the 85°C power dissipation curves in the
Typical Performance Characteristics section to estimate the
13
www.national.com
LMZ12002EXT
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3536IDD#TRPBF | 4 A SWITCHING REGULATOR, 1440 kHz SWITCHING FREQ-MAX, PDSO10 |
| LM4576-3.3BT | 3.5 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, PSFM5 |
| LS1501-7ERD6TB1 | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LC5523FLF3052 | POWER FACTOR CONTROLLER, 18 kHz SWITCHING FREQ-MAX, ZFM7 |
| LK1001-7D7 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LMZ12002EXTTZNOPB | 制造商:National Semiconductor 功能描述:Simple Switcher Power Module 7-Pin TO-PMOD T/R |
| LMZ12002EXTTZX/NOPB | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LMZ12002TZ-ADJ | 制造商:NSC 制造商全称:National Semiconductor 功能描述:2A SIMPLE SWITCHER? Power Module with 20V Maximum Input Voltage |
| LMZ12002TZ-ADJ/NOPB | 功能描述:DC/DC转换器 12V,2A PWR MODULE RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LMZ12002TZADJNOPB | 制造商:Texas Instruments 功能描述:Module DC-DC 1-OUT 0.8V to 6V 2A 7-Pin TO-PMOD EP |
发布紧急采购，3分钟左右您将得到回复。