- 您现在的位置：买卖IC网 > Datasheet目录866 > LMZ14201TZE-ADJ/NOPB (National Semiconductor)IC BUCK SYNC ADJ 1A TO-PMOD-7 Datasheet资料下载
参数资料
| 型号： | LMZ14201TZE-ADJ/NOPB |
| 厂商： | National Semiconductor |
| 文件页数： | 12/27页 |
| 文件大小： | 0K |
| 描述： | IC BUCK SYNC ADJ 1A TO-PMOD-7 |
| 产品培训模块： | SIMPLE SWITCHER Power Modules |
| 视频文件： | Power Design Invitational - Another Geek Moment |
| 标准包装： | 45 |
| 系列： | SIMPLE SWITCHER® |
| 类型： | 非隔离（POL） |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 6V |
| 电压 - 输入（最大）： | 42V |
| Voltage - Output 1： | 0.8 ~ 6 V |
| 电流 - 输出（最大）： | 1A |
| 电源（瓦） - 制造商系列： | 6W |
| 特点： | 带有 UVLO |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-PMOD-7，电源模块 |
| 尺寸/尺寸： | 0.40" L x 0.54" W x 0.18" H（10.2mm x 13.8mm x 4.6mm） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
| 效率： | 90% |
| 电源（瓦特）- 最大： | 6W |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
LMZ14201
SNVS649F – JANUARY 2010 – REVISED OCTOBER 2013
www.ti.com
COT CONTROL CIRCUIT OVERVIEW
Constant On Time control is based on a comparator and an on-time one shot, with the output voltage feedback
compared with an internal 0.8V reference. If the feedback voltage is below the reference, the main MOSFET is
turned on for a fixed on-time determined by a programming resistor R ON . R ON is connected to V IN such that on-
time is reduced with increasing input supply voltage. Following this on-time, the main MOSFET remains off for a
minimum of 260 ns. If the voltage on the feedback pin falls below the reference level again the on-time cycle is
repeated. Regulation is achieved in this manner.
Design Steps for the LMZ14201 Application
The LMZ14201 is fully supported by Webench? and offers the following: Component selection, electrical and
thermal simulations as well as the build-it board for a reduction in design time. The following list of steps can be
used to manually design the LMZ14201 application.
?
?
?
?
?
?
?
?
Select minimum operating V IN with enable divider resistors
Program V O with divider resistor selection
Program turn-on time with soft-start capacitor selection
Select C O
Select C IN
Set operating frequency with R ON
Determine module dissipation
Layout PCB for required thermal performance
ENABLE DIVIDER, R ENT AND R ENB SELECTION
The enable input provides a precise 1.18V band-gap rising threshold to allow direct logic drive or connection to a
voltage divider from a higher enable voltage such as V IN . The enable input also incorporates 90 mV (typ) of
hysteresis resulting in a falling threshold of 1.09V. The maximum recommended voltage into the EN pin is 6.5V.
For applications where the midpoint of the enable divider exceeds 6.5V, a small zener can be added to limit this
voltage.
The function of this resistive divider is to allow the designer to choose an input voltage below which the circuit
will be disabled. This implements the feature of programmable under voltage lockout. This is often used in
battery powered systems to prevent deep discharge of the system battery. It is also useful in system designs for
sequencing of output rails or to prevent early turn-on of the supply as the main input voltage rail rises at power-
up. Applying the enable divider to the main input rail is often done in the case of higher input voltage systems
such as 24V AC/DC systems where a lower boundary of operation should be established. In the case of
sequencing supplies, the divider is connected to a rail that becomes active earlier in the power-up cycle than the
LMZ14201 output rail. The two resistors should be chosen based on the following ratio:
R ENT / R ENB = (V IN UVLO / 1.18V) – 1
(1)
The LMZ14201 demonstration and evaluation boards use 11.8k ? for R ENB and 68.1k ? for R ENT resulting in a
rising UVLO of 8V. This divider presents 6.25V to the EN input when the divider input is raised to 42V.
The EN pin is internally pulled up to VIN and can be left floating for always-on operation.
OUTPUT VOLTAGE SELECTION
Output voltage is determined by a divider of two resistors connected between V O and ground. The midpoint of
the divider is connected to the FB input. The voltage at FB is compared to a 0.8V internal reference. In normal
operation an on-time cycle is initiated when the voltage on the FB pin falls below 0.8V. The main MOSFET on-
time cycle causes the output voltage to rise and the voltage at the FB to exceed 0.8V. As long as the voltage at
FB is above 0.8V, on-time cycles will not occur.
The regulated output voltage determined by the external divider resistors RFBT and RFBB is:
V O = 0.8V * (1 + R FBT / R FBB )
Rearranging terms; the ratio of the feedback resistors for a desired output voltage is:
R FBT / R FBB = (V O / 0.8V) - 1
These resistors should be chosen from values in the range of 1.0 kohm to 10.0 kohm.
(2)
(3)
12
Submit Documentation Feedback
Product Folder Links: LMZ14201
Copyright ? 2010–2013, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| LMZ14203EXTTZE/NOPB | IC BUCK SYNC ADJ 3A TO-PMOD-7 |
| LNC2W153MSEJ | CAP ALUM 15000UF 450V 20% SCREW |
| LNK2H822MSEJ | CAP ALUM 8200UF 500V 20% SCREW |
| LNT2H103MSEJ | CAP ALUM 10000UF 500V 20% SCREW |
| LNX2J562MSEK | CAP ALUM 5600UF 630V 20% SCREW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LMZ14201TZX-ADJ | 制造商:NSC 制造商全称:National Semiconductor 功能描述:1A SIMPLE SWITCHER? Power Module with 42V Maximum Input Voltage |
| LMZ14201TZX-ADJ/NOPB | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LMZ14201TZXADJNOPB | 制造商:Texas Instruments 功能描述:Module DC-DC 1-OUT 0.8V to 6V 1A 7-Pin TO-PMOD EP |
| LMZ14202 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:2A SIMPLE SWITCHER? Power Module with 42V Maximum Input Voltage |
| LMZ14202_1 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:2A SIMPLE SWITCHER?? Power Module with 42V Maximum Input Voltage |
发布紧急采购，3分钟左右您将得到回复。