- 您现在的位置：买卖IC网 > PDF目录44715 > LNBK20D2 (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PDSO20 PDF资料下载
参数资料
| 型号： | LNBK20D2 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封装： | SO-20 |
| 文件页数： | 3/14页 |
| 文件大小： | 467K |
| 代理商： | LNBK20D2 |
LNBK20D2
11/14
THERMAL DESIGN NOTE
During normal operation, this device dissipates some power. At maximum rated output current (400mA),
the voltage drop on the linear regulator lead to a total dissipated power that is of about 2W. The heat
generated requires a suitable heatsink to keep the junction temperature below the over temperature
protection threshold. Assuming a 40°C temperature inside the Set-Top-Box case, the total Rthj-amb has
to be less than 43°C/W.
While this can be easily achieved using a through-hole power package that can be attached to a small
heatsink or to the metallic frame of the receiver, a surface mount power package must rely on PCB
solutions whose thermal efficiency is often limited. The simplest solution is to use a large, continuous
copper area of the GND layer to dissipate the heat coming from the IC body.
The SO-20 package of this IC has 4 GND pins that are not just intended for electrical GND connection, but
also to provide a low thermal resistance path between the silicon chip and the PCB heatsink. Given an
Rthj-c equal to 15°C/W, a maximum of 28°C/W are left to the PCB heatsink. This figure is achieved if a
minimum of 25cm2 copper area is placed just below the IC body. This area can be the inner GND layer of
a multi-layer PCB, or, in a dual layer PCB, an unbroken GND area even on the opposite side where the
IC is placed. In both cases, the thermal path between the IC GND pins and the dissipating copper area
must exhibit a low thermal resistance.
In figure 4, it is shown a suggested layout for the SO-20 package with a dual layer PCB, where the IC
Ground pins and the square dissipating area are thermally connected through 32 vias holes, filled by
solder. This arrangement, when L=50mm, achieves an Rthc-a of about 28°C/W.
Different layouts are possible, too. Basic principles, however, suggest to keep the IC and its ground pins
approximately in the middle of the dissipating area; to provide as many vias as possible; to design a
dissipating area having a shape as square as possible and not interrupted by other copper traces.
SO-20 SUGGESTED PCB HEATSINK LAYOUT
相关PDF资料 |
PDF描述 |
|---|---|
| LNBP10SP-TR | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| LNBP12SP-TR | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| LNBP16SP-TR | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| LNBP15SP-TR | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| LNBP14SP-TR | SPECIALTY ANALOG CIRCUIT, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LNBK20D2-TR | 功能描述:线性稳压器 - 标准 LNB SUPPLY AND CONTROL Vltg REG RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
| LNBK20PD | 功能描述:IC LNB SUPPLY & CNTRL 20-PWRSOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
| LNBK20PD-TR | 功能描述:线性稳压器 - 标准 VOLTAGE REGULATOR RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
| LNBP10 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:LNB SUPPLY AND CONTROL VOLTAGE REGULATOR PARALLEL INTERFACE |
| LNBP10LPUR | 功能描述:线性稳压器 - 标准 LNB SUP/CTRL VLT REG RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
发布紧急采购，3分钟左右您将得到回复。