- 您现在的位置：买卖IC网 > PDF目录44716 > LNK305G-TL (POWER INTEGRATIONS INC) 0.8 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8 PDF资料下载
参数资料
| 型号： | LNK305G-TL |
| 厂商： | POWER INTEGRATIONS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 0.8 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封装： | PLASTIC SURFACE MOUNT, DIP-8 |
| 文件页数： | 19/20页 |
| 文件大小： | 706K |
| 代理商： | LNK305G-TL |
2-8
Rev. I 11/08
8
LNK302/304-306
Pre-load Resistor R4
In high-side, direct feedback designs where the minimum load
is <3 mA, a pre-load resistor is required to maintain output
regulation. This ensures sufcient inductor energy to pull the
inductor side of the feedback capacitor C3 to input return via
D2. The value of R4 should be selected to give a minimum
output load of 3 mA.
In designs with an optocoupler the Zener or reference bias
current provides a 1 mA to 2 mA minimum load, preventing
“pulse bunching” and increased output ripple at zero load.
LinkSwitch-TN Layout Considerations
In the buck or buck-boost converter conguration, since the
SOURCE pins in LinkSwitch-TN are switching nodes, the copper
area connected to SOURCE should be minimized to minimize
EMI within the thermal constraints of the design.
In the boost conguration, since the SOURCE pins are tied
to DC return, the copper area connected to SOURCE can be
maximized to improve heatsinking.
The loop formed between the LinkSwitch-TN, inductor (L1),
freewheeling diode (D1), and output capacitor (C2) should
be kept as small as possible. The BYPASS pin capacitor
C1 (Figure 6) should be located physically close to the
SOURCE (S) and BYPASS (BP) pins. To minimize direct
coupling from switching nodes, the LinkSwitch-TN should be
placed away from AC input lines. It may be advantageous to
place capacitors C4 and C5 in-between LinkSwitch-TN and the
AC input. The second rectier diode D4 is optional, but may
be included for better EMI performance and higher line surge
withstand capability.
Quick Design Checklist
As with any power supply design, all LinkSwitch-TN designs
should be veried for proper functionality on the bench. The
following minimum tests are recommended:
1) Adequate DC rail voltage – check that the minimum DC
input voltage does not fall below 70 VDC at maximum load,
minimum input voltage.
2) Correct Diode Selection – UF400x series diodes are
recommended only for designs that operate in MDCM at
an ambient of 70
°C or below. For designs operating in
continuous conduction mode (CCM) and/or higher ambients,
then a diode with a reverse recovery time of 35 ns or better,
such as the BYV26C, is recommended.
3) Maximum drain current – verify that the peak drain current
is below the data sheet peak drain specication under
worst-case conditions of highest line voltage, maximum
overload (just prior to auto-restart) and highest ambient
temperature.
4) Thermal check – at maximum output power, minimum
input voltage and maximum ambient temperature, verify
that the LinkSwitch-TN SOURCE pin temperature is
100
°C or below. This gure ensures adequate margin due
to variations in R
DS(ON) from part to part. A battery powered
thermocouple meter is recommended to make measurements
when the SOURCE pins are a switching node.Alternatively,
the ambient temperature may be raised to indicate margin
to thermal shutdown.
In a LinkSwitch-TN design using a buck or buck boost converter
topology, the SOURCE pin is a switching node. Oscilloscope
measurements should therefore be made with probe grounded
to a DC voltage, such as primary return or DC input rail, and
not to the SOURCE pins. The power supply input must always
be supplied from an isolated source (e.g. via an isolation
transformer).
相关PDF资料 |
PDF描述 |
|---|---|
| LNK302DG | 0.2 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8 |
| LNK305DG-TL | 0.8 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8 |
| LNK306DG | 1.4 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8 |
| LNK302D-TL | 0.2 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8 |
| LNK305DG | 0.8 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LNK305P | 功能描述:IC OFFLINE SWIT OCP 8DIP RoHS:否 类别:集成电路 (IC) >> PMIC - AC-DC 转换器，离线开关 系列:LinkSwitch®-TN 标准包装:1 系列:FPS™ 输出隔离:隔离 频率范围:61kHz ~ 73kHz 输入电压:8 V ~ 26 V 输出电压:650V 功率（瓦特）:12W 工作温度:-40°C ~ 115°C 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-MDIP 包装:Digi-Reel® 其它名称:FSL206MRBNFSDKR |
| LNK305P（3-5W） | 制造商:未知厂家 制造商全称:未知厂家 功能描述:（3-5W)电源方案 |
| LNK305P(4-7W） | 制造商:未知厂家 制造商全称:未知厂家 功能描述:（4-7W电源方案） |
| LNK305P/G | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Lowest Component Count. Energy Efficient Off-Line Switcher IC |
| LNK305P/G/D | 制造商:FERYSTER 制造商全称:FERYSTER Inductive Components Manufacturer 功能描述:Lowest Component Count, Energy-Effi cient Off-Line Switcher IC |
发布紧急采购，3分钟左右您将得到回复。