- 您现在的位置：买卖IC网 > PDF目录19769 > LNK616GG-TL (Power Integrations)IC OFFLINE SWIT CV/CC HV 8SMD PDF资料下载
参数资料
| 型号： | LNK616GG-TL |
| 厂商： | Power Integrations |
| 文件页数： | 4/18页 |
| 文件大小： | 0K |
| 描述： | IC OFFLINE SWIT CV/CC HV 8SMD |
| 应用说明： | LinkSwitch-II Family, Appl Note AN-44 |
| 产品培训模块： | LinkSwitch-II Overview |
| 标准包装： | 1,000 |
| 系列： | LinkSwitch®-II |
| 输出隔离： | 隔离 |
| 频率范围： | 58kHz ~ 72kHz |
| 输出电压： | 700V |
| 功率（瓦特）： | 6.1W |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 8-SMD（7 个接脚），鸥形翼 |
| 供应商设备封装： | SMD-8C |
| 包装： | 带卷 (TR) |
| 配用： | 596-1235-ND - KIT REF DESIGN LINKSWITCH 2 |
LNK603-606/613-616
Applications Example
C6
1 nF R7
100 V 200 ?
L1
1.5 mH
5
T1
EE16
10
5 V, 555 mA
820 pF 3
AC
Input
RF1
8.2 ?
2W
D1
1N4007
D2
1N4007
C1
4.7 μ F
400 V
R2
470 k ?
C2
4.7 μ F
400 V
R3
300 ?
D5
1N4007
C3
1 kV
8
1
2
4
D7
SS14
C7
680 μ F
10 V
R8
200 ?
VR1
2MM5230B-7
4.7 V
DC
Output
D3
1N4007
D4
1N4007
D
LinkSwitch-II
U1
LNK613DG
FB
NC
D6
LL4148
R5
13 k ?
1%
BP
S
C4
1 μ F
25 V
R4
6.2 k ? C5
10 μ F
16 V
R6
8.87 k ?
1%
PI-5111-050808
Figure 4.
Energy Efficient USB Charger Power Supply (74% Average Efficiency, <30 mW No-load Input Power).
Circuit Description
This circuit shown in Figure 4 is configured as a primary-side
regulated flyback power supply utilizing the LNK613DG. With
an average efficiency of 74% and <30 mW no-load input power
this design easily exceeds the most stringent current energy
efficiency requirements.
Input Filter
AC input power is rectified by diodes D1 through D4. The
rectified DC is filtered by the bulk storage capacitors C1 and
C2. Inductor L1, C1 and C2 form a pi (π) filter, which attenuates
conducted differential-mode EMI noise. This configuration
along with Power Integrations transformer E-shield ? technology
allow this design to meet EMI standard EN55022 class B with
good margin without requiring a Y capacitor, even with the
output connected to safety earth ground. Fusible resistor RF1
provides protection against catastrophic failure. This should be
suitably rated (typically a wire wound type) to withstand the
instantaneous dissipation while the input capacitors charge
when first connected to the AC line.
LNK 613 Primary
The LNK613DG device (U1) incorporates the power switching
device, oscillator, CC/CV control engine, startup, and protection
functions. The integrated 700 V MOSFET provides a large drain
voltage margin in universal input AC applications, increasing
reliability and also reducing the output diode voltage stress by
allowing a greater transformer turns ratio. The device is
completely self-powered from the BYPASS pin and decoupling
capacitor C4. For the LNK61X devices, the bypass capacitor
value also selects the amount of output cable voltage drop
4
Rev. F 01/10
compensation. A 1 m F value selects the standard compensation.
A 10 m F value selects the enhanced compensation. Table 2
shows the amount of compensation for each device and
bypass capacitor value. The LNK60x devices do not provide
cable drop compensation.
The optional bias supply formed by D6 and C5 provides the
operating current for U1 via resistor R4. This reduces the
no-load consumption from ~200 mW to <30 mW and also
increases light load efficiency.
The rectified and filtered input voltage is applied to one side of
the primary winding of T1. The other side of the transformer’s
primary winding is driven by the integrated MOSFET in U1. The
leakage inductance drain voltage spike is limited by an RCD-R
clamp consisting of D5, R2, R3, and C3.
Output Rectification
The secondary of the transformer is rectified by D7, a 1 A, 40 V
Schottky barrier type for higher efficiency, and filtered by C7. If
lower efficiency is acceptable then this can be replaced with a
1 A PN junction diode for lower cost. In this application C7 was
sized to meet the required output voltage ripple specification
without requiring a post LC filter. To meet battery self discharge
requirement the pre-load resistor has been replaced with a
series resistor and Zener network (R8 and VR1). However in
designs where this is not a requirement a standard 1 k W
resistor can be used.
Output Regulation
The LNK613 regulates the output using ON/OFF control in the
constant voltage (CV) regulation region of the output character-
www.powerint.com
相关PDF资料 |
PDF描述 |
|---|---|
| TPSA335M025R1500 | CAP TANT 3.3UF 25V 20% 1206 |
| ISPLSI 1024EA-125LT100 | IC PLD ISP 48I/O 7.5NS 100TQFP |
| HCC06DRYN-S13 | CONN EDGECARD 12POS .100 EXTEND |
| LNK606GG-TL | IC OFFLINE SWIT CV/CC HV 8SOIC |
| FMM12DSEH-S13 | CONN EDGECARD 24POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LNK616PG | 功能描述:交流/直流开关转换器 85-265 VAC 5.5W LinkSwitch II RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| LNK616PG-TL | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:Energy-Efficient, Accurate CV/CC Switcher for Adapters and Chargers |
| LNK623 | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:Energy-Effi cient, Off-line Switcher with Accurate Primary-side Constant-Voltage (CV) Control |
| LNK623DG | 功能描述:交流/直流开关转换器 5.0 W (85-265 VAC) RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| LNK623DG-TL | 功能描述:交流/直流开关转换器 5.0 W (85-265 VAC) RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。