- 您现在的位置：买卖IC网 > PDF目录44716 > LOG102AIDR (TEXAS INSTRUMENTS INC) LOG OR ANTILOG AMPLIFIER, 1.4 MHz BAND WIDTH, PDSO14 PDF资料下载
参数资料
| 型号： | LOG102AIDR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 模拟运算功能 |
| 英文描述： | LOG OR ANTILOG AMPLIFIER, 1.4 MHz BAND WIDTH, PDSO14 |
| 封装： | GREEN, PLASTIC, MS-012AB, SOIC-14 |
| 文件页数： | 3/18页 |
| 文件大小： | 490K |
| 代理商： | LOG102AIDR |
www.ti.com
LOG102
11
SBOS211B
DEFINITION OF TERMS
TRANSFER FUNCTION
The ideal transfer function is:
VOUT = 1V logI1/I2
Figure 14 shows the graphical representation of the transfer
over valid operating range for the LOG102.
FIGURE 14. Transfer Function with Varying I2 and I1.
ACCURACY
Accuracy considerations for a log ratio amplifier are some-
what more complicated than for other amplifiers. This is
because the transfer function is nonlinear and has two
inputs, each of which can vary over a wide dynamic range.
The accuracy for any combination of inputs is determined
from the total error specification.
TOTAL ERROR
The total error is the deviation (expressed in mV) of the
actual output from the ideal output of VOUT = 1V log(I1/I2).
Thus,
VOUT (ACTUAL) = VOUT (IDEAL) ± Total Error.
It represents the sum of all the individual components of error
normally associated with the log amp when operated in the
current input mode. The worst-case error for any given ratio
of I1/I2 is the largest of the two errors when I1 and I2 are
considered separately; this case is shown in Table I. Tem-
perature can affect total error.
ERRORS RTO AND RTI
As with any transfer function, errors generated by the func-
tion itself may be Referred-to-Output (RTO) or Referred-to-
Input (RTI). In this respect, log amps have a unique property:
Given some error voltage at the log amp’s output, that error
corresponds to a constant percent of the input regardless of
the actual input level.
LOG CONFORMITY
For the LOG102, log conformity is calculated the same as
linearity and is plotted I1/I2 on a semi-log scale. In many
applications, log conformity is the most important specifica-
tion. This is true because bias current errors are negligible
(1pA compared to input currents of 1nA and above) and the
scale factor and offset errors may be trimmed to zero or
removed by system calibration. This leaves log conformity as
the major source of error.
Log conformity is defined as the peak deviation from the best
fit straight line of the VOUT versus log (I1/I2) curve. This is
expressed as a percent of ideal full-scale output. Thus, the
nonlinearity error expressed in volts over m decades is:
VOUT (NONLIN) = 1V/dec 2Nm V
where N is the log conformity error, in percent.
INDIVIDUAL ERROR COMPONENTS
The ideal transfer function with current input is:
VV
I
OUT =
( )
1
2
log
The actual transfer function with the major components of
error is:
VV
K
II
Nm
V
OUT
B
OS OUT
=
( ) ±
(
)
±±
11
2
1
2
log
–
The individual component of error is:
K = gain accuracy (0.3%, typ), as specified in
specification table.
IB1 = bias current of A1 (5pA, typ)
IB2 = bias current of A2 (5pA, typ)
N = log conformity error (0.04%, 0.15%, typ)
0.04% for n = 5, 0.15% for n = 6
VOS OUT = output offset voltage (1mV, typ)
n = number of decades over which N is specified:
Example: what is the error when
I1 = 1A and I2 = 100nA
I1 (maximum error)(1)
10nA
100nA
1
A
(30mV)
(25mV)
(20mV)
100nA
(25mV)
30mV
25mV
1
A
(20mV)
30mV
25mV
20mV
10
A
(25mV)
30mV
25mV
NOTE: (1) Maximum errors are in parenthesis.
I2
(maximum
error)(1)
TABLE I. I1/I2 and Maximum Errors.
(5)
3
2
1
0
–3
1
A10A 100A
1mA
100nA
10nA
V
OUT = (1V) LOG
Dashed Line = Greater
Supply Voltage Requirement
I
1
I
2
V
OUT
(V)
I 2=
10
nA
I 2=
10
0nA
I 2=
1nA
I 2=
1
A
I 2=
1
00
A
I 2=
1
0
A
I 2=
1
m
A
I
1
(5)
(6)
(7)
(8)
(9)
相关PDF资料 |
PDF描述 |
|---|---|
| LOG102AIDG4 | LOG OR ANTILOG AMPLIFIER, 1.4 MHz BAND WIDTH, PDSO14 |
| LOG114AIRGVTG4 | LOG OR ANTILOG AMPLIFIER, PQCC16 |
| LOG114AIRGVRG4 | LOG OR ANTILOG AMPLIFIER, PQCC16 |
| LOG114AIRGVT | LOG OR ANTILOG AMPLIFIER, PQCC16 |
| LOG2112AIDWE4 | LOG OR ANTILOG AMPLIFIER, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LOG102AIDRG4 | 功能描述:对数放大器 Logarithmic and Log Ratio Amp RoHS:否 制造商:Texas Instruments 通道数量:3 带宽:3 dB 共模抑制比（最小值）: 输入补偿电压:+/- 7 mV 输入电压范围（最大值）:5.5 V 工作电源电压:4.5 V to 5.5 V 电源电流:+/- 15 mA 工作温度范围:- 40 C to +85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel |
| LOG104 | 制造商:TI 制造商全称:Texas Instruments 功能描述:LOGARITHMIC AND LOG RATIO AMPLIFIER |
| LOG104AID | 功能描述:对数放大器 LOGARITHMIC AMP RoHS:否 制造商:Texas Instruments 通道数量:3 带宽:3 dB 共模抑制比（最小值）: 输入补偿电压:+/- 7 mV 输入电压范围（最大值）:5.5 V 工作电源电压:4.5 V to 5.5 V 电源电流:+/- 15 mA 工作温度范围:- 40 C to +85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel |
| LOG104AID | 制造商:Texas Instruments 功能描述:IC AMP LOG SMD SOIC8 104 |
| LOG104AIDE4 | 功能描述:对数放大器 LOGARITHMIC AMP RoHS:否 制造商:Texas Instruments 通道数量:3 带宽:3 dB 共模抑制比（最小值）: 输入补偿电压:+/- 7 mV 输入电压范围（最大值）:5.5 V 工作电源电压:4.5 V to 5.5 V 电源电流:+/- 15 mA 工作温度范围:- 40 C to +85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。