- 您现在的位置：买卖IC网 > PDF目录79749 > LP3907SQX-JIXI (NATIONAL SEMICONDUCTOR CORP) 1.5 A DUAL SWITCHING CONTROLLER, 2100 kHz SWITCHING FREQ-MAX, QCC24 PDF资料下载
参数资料
| 型号： | LP3907SQX-JIXI |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 1.5 A DUAL SWITCHING CONTROLLER, 2100 kHz SWITCHING FREQ-MAX, QCC24 |
| 封装： | 4 X 4 MM, 0.8 MM HEIGHT, LLP-24 |
| 文件页数： | 11/44页 |
| 文件大小： | 3058K |
| 代理商： | LP3907SQX-JIXI |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
tions. When the output drops below the ‘low’ PFM threshold,
the cycle repeats to restore the output voltage to ~1.6% above
the nominal PWM output voltage.
If the load current should increase during PFM mode (see
figure below) causing the output voltage to fall below the
‘low2’ PFM threshold, the part will automatically transition into
fixed-frequency PWM mode.
SW1, SW2 OPERATION
SW1 and SW2 have selectable output voltages ranging from
0.8V to 3.5V (typ.). Both SW1 and SW2 in the LP3907 are
I2C register controlled and are enabled by default through the
internal state machine of the LP3907 following a Power-On
event that moves the operating mode to the Active state. (see
Power On Sequence). The SW1 and SW2 output voltages
revert to default values when the power on sequence has
been completed. The default output voltage for each buck
converter is factory programmable. (See Application Notes).
SW1, SW2 CONTROL REGISTERS
SW1, SW2 can be enabled/disabled through the correspond-
ing control register.
The Modulation mode PWM/PFM is by default automatic and
depends on the load as described above in the functional de-
scription. The modulation mode can be overridden by setting
I2C bit to a logic 1 in the corresponding buck control register,
forcing the buck to operate in PWM mode regardless of the
load condition.
30017814
SHUTDOWN MODE
During shutdown the PFET switch, reference, control and
bias circuitry of the converters are turned off. The NFET
switch will be on in shutdown to discharge the output. When
the converter is enabled, soft start is activated. It is recom-
mended to disable the converter during the system power up
and under voltage conditions when the supply is less than
2.8V.
SOFT START
The soft-start feature allows the power converter to gradually
reach the initial steady state operating point, thus reducing
start-up stresses and surges. The two LP3907 buck convert-
ers have a soft-start circuit that limits in-rush current during
start-up. During start-up the switch current limit is increased
in steps. Soft start is activated only if EN goes from logic low
to logic high after V
IN reaches 2.8V. Soft start is implemented
by increasing switch current limit in steps of 180mA, 300mA,
and 720mA for Buck1; 161mA, 300mA and 536mA for Buck2
(typ. Switch current limit). The start-up time thereby depends
on the output capacitor and load current demanded at start-
up.
LOW DROPOUT OPERATION
The LP3907 can operate at 100% duty cycle (no switching;
PMOS switch completely on) for low drop out support of the
output voltage. In this way the output voltage will be controlled
down to the lowest possible input voltage. When the device
operates near 100% duty cycle, output voltage ripple is ap-
proximately 25mV. The minimum input voltage needed to
support the output voltage is
V
IN, MIN = ILOAD * (RDSON, PFET + RINDUCTOR) + VOUT
— ILOAD
Load current
— RDSON, PFET
Drain to source resistance of
PFET switch in the triode region
— RINDUCTOR
Inductor resistance
19
www.national.com
LP3907
相关PDF资料 |
PDF描述 |
|---|---|
| LT1004IPWRG4-1-2 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.235 V, PDSO8 |
| LTC2912HDDB-3#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LK1501-9EPDD | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1501-9ERD3B1 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1501-9ERD6B1 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LP3907SQX-JXQX | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual High-Current Step-Down DC/DC and Dual Linear Regulator with I2C Compatible Interface |
| LP3907SQX-JXQX/NOPB | 功能描述:其他电源管理 RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| LP3907SQX-PFX6W/NOPB | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| LP3907SQX-PJXIX/NOPB | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| LP3907SQX-PXPP | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual High-Current Step-Down DC/DC and Dual Linear Regulator with I2C Compatible Interface |
发布紧急采购，3分钟左右您将得到回复。