参数资料
型号: LPC1342FBD48,118
厂商: NXP Semiconductors
文件页数: 11/74页
文件大小: 0K
描述: IC MCU 32BIT 32KB FLASH 48LQFP
标准包装: 2,000
系列: LPC13xx
核心处理器: ARM? Cortex?-M3
芯体尺寸: 32-位
速度: 72MHz
连通性: I²C,Microwire,SPI,SSI,SSP,UART/USART,USB
外围设备: 欠压检测/复位,POR,WDT
输入/输出数: 42
程序存储器容量: 16KB(16K x 8)
程序存储器类型: 闪存
RAM 容量: 4K x 8
电压 - 电源 (Vcc/Vdd): 2 V ~ 3.6 V
数据转换器: A/D 8x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 48-LQFP
包装: 带卷 (TR)
LPC1311_13_42_43
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 5 — 6 June 2012
19 of 74
NXP Semiconductors
LPC1311/13/42/43
32-bit ARM Cortex-M3 microcontroller
7.6.1 Features
Controls system exceptions and peripheral interrupts.
On the LPC1311/13/42/43, the NVIC supports up to 17 vectored interrupts. In
addition, up to 40 of the individual GPIO inputs are NVIC-vector capable.
8 programmable interrupt priority levels, with hardware priority level masking
Relocatable vector table.
Software interrupt generation.
7.6.2 Interrupt sources
Each peripheral device has one interrupt line connected to the NVIC but may have several
interrupt flags. Individual interrupt flags may also represent more than one interrupt
source.
Any GPIO pin (total of up to 42 pins) regardless of the selected function, can be
programmed to generate an interrupt on a level, or rising edge or falling edge, or both.
7.7 IOCONFIG block
The IOCONFIG block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on-chip peripherals.
Peripherals should be connected to the appropriate pins prior to being activated and prior
to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is
not mapped to a related pin should be considered undefined.
7.8 Fast general purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Multiple outputs
can be set or cleared in one write operation.
LPC1311/13/42/43 use accelerated GPIO functions:
GPIO block is a dedicated AHB peripheral so that the fastest possible I/O timing can
be achieved.
Entire port value can be written in one instruction.
Additionally, any GPIO pin (total of up to 42 pins) providing a digital function can be
programmed to generate an interrupt on a level, a rising or falling edge, or both.
7.8.1 Features
Bit level port registers allow a single instruction to set or clear any number of bits in
one write operation.
Direction control of individual bits.
All I/O default to inputs with pull-up resistors enabled after reset with the exception of
the I2C-bus pins PIO0_4 and PIO0_5.
Pull-up/pull-down resistor configuration can be programmed through the IOCONFIG
block for each GPIO pin.
相关PDF资料
PDF描述
VI-BNL-IW-F1 CONVERTER MOD DC/DC 28V 100W
P89LPC934FDH,529 IC 80C51 MCU FLASH 8K 28-TSSOP
VI-BNK-IX-F4 CONVERTER MOD DC/DC 40V 75W
VI-BNK-IX-F2 CONVERTER MOD DC/DC 40V 75W
VI-BNK-IX-F1 CONVERTER MOD DC/DC 40V 75W
相关代理商/技术参数
参数描述
LPC1342FHN33 制造商:NXP Semiconductors 功能描述:MCU 32BIT 16KFLASH CORTEX-M3 33HVQFN 制造商:NXP Semiconductors 功能描述:MCU, 32BIT, 16KFLASH, CORTEX-M3, 33HVQFN
LPC1342FHN33,518 功能描述:8位微控制器 -MCU 32B ARM CORTEXM3 MCU 16KB FL 4KB SRAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
LPC1342FHN33,551 功能描述:ARM微控制器 - MCU 32-bit ARM Cortex-M3 16kb Flash RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
LPC1342FHN33551 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU ARM 72MHZ HVQFN-33 制造商:NXP Semiconductors 功能描述:MCU 32BIT ARM CORTEX M3 32HVQFN
LPC1343 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:32-bit ARM Cortex-M3 microcontroller up to 32 kB flash and 8 kB SRAM USB device