- 您现在的位置：买卖IC网 > PDF目录32308 > LSM-0.8/10-D5-C (MURATA POWER SOLUTIONS INC) 1-OUTPUT 8 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | LSM-0.8/10-D5-C |
| 厂商： | MURATA POWER SOLUTIONS INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 8 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, SMT-6 |
| 文件页数： | 9/13页 |
| 文件大小： | 460K |
| 代理商： | LSM-0.8/10-D5-C |
Output Overcurrent Detection
Overloading the power converter's output for an extended time will invariably
cause internal component temperatures to exceed their maximum ratings and
eventually lead to component failure. High-current-carrying components such
as inductors, FET's and diodes are at the highest risk. LSM D5 SMT Series
DC/DC converters incorporate an output overcurrent detection and shutdown
function that serves to protect both the power converter and its load.
If the output current exceeds it maximum rating by typically 70% (17 Amps) or
if the output voltage drops to less than 98% of it original value, the LSM D5's
internal overcurrent-detection circuitry immediately turns off the converter,
which then goes into a "hiccup" mode. While hiccupping, the converter will
continuously attempt to restart itself, go into overcurrent, and then shut down.
Under these conditions, the average output current will be approximately
600mA, and the average input current will be approximately 60mA. Once the
output short is removed, the converter will automatically restart itself.
Output Voltage Trimming
Allowable trim ranges for each model in the LSM D5 SMT Series are ±10%.
Trimming is accomplished with either a trimpot or a single xed resistor. The
trimpot should be connected between +Output and Common with its wiper
connected to the Trim pin as shown in Figure 6 below.
A trimpot can be used to determine the value of a single xed resistor
which can then be connected, as shown in Figure 7, between the Trim pin
and +Output to trim down the output voltage, or between the Trim pin and
Common to trim up the output voltage. Fixed resistors should have absolute
TCR’s less than 100ppm/ C to ensure stability.
The equations below can be starting points for selecting specic trim-resistor
values. Recall, untrimmed devices are guaranteed to be ±1% accurate.
Adjustment beyond the specied ±10% adjustment range is not recommended.
When using trim in combination with Remote Sense, the maximum rated power
must not be exceeded (see Remote Sense).
On/Off Control
The On/Off Control pin may be used for remote on/off operation. LSM D5
Series DC/DC converters are designed so that they are enabled when the
control pin is left open (open collector) and disabled when the control pin is
pulled low (to less than +0.8V relative to Common). As shown in Figure 4, all
models have an internal 5k
Ω pull-up resistor to VIN (+Input).
Dynamic control of the on/off function is best accomplished with a mechanical
relay or open-collector/open-drain drive circuit (optically isolated if appropri-
ate). The drive circuit should be able to sink appropriate current when
activated and withstand appropriate voltage when deactivated.
Applying an external voltage to the On/Off Control pin when no input power is
applied to the converter can cause permanent damage to the converter. The
on/off control function, however, is designed such that the converter can be
disabled (control pin pulled low) while input voltage is ramping up and then
"released" once the input has stabilized (see also power-up sequencing).
Figure 5. Driving the External Power-Up Open Collector
ON/OFF pin open: Logic High = DC/DC converter On
ON/OFF pin <0.4V: Logic Low = DC/DC converter Off
External Input Open: On/Off pin Low = DC/DC converter Off
External Input Low: On/Off pin High = DC/DC converter On
Power-up sequencing
If a controlled start-up of one or more LSM D5 Series DC/DC converters
is required, or if several output voltages need to be powered-up in a given
sequence, the On/Off control pin can be driven with an external open collector
device as per Figure 5.
Leaving the input of the external circuit open during power-up will have the
output of the DC/DC converter disabled. When the input to the external open
collector is pulled low, the DC/DC converters output will be enabled.
Output Overvoltage Protection
LSM D5 SMT Series DC/DC converters do not incorporate output overvolt-
age protection. In the extremely rare situation in which the device’s feedback
loop is broken, the output voltage may run to excessively high levels (VOUT =
VIN). If it is absolutely imperative that you protect your load against any and
all possible overvoltage situations, voltage limiting circuitry must be provided
external to the power converter.
Figure 4. Driving the On/Off Control Pin with an Open-Collector Drive Circuit
+INPUT
COMMON
EXTERNAL
OPEN
COLLECTOR
INPUT
5k
10k
LSM-10A D5 Models
Single Output, Non-Isolated, 5VIN, 0.8-3.3VOUT, 10A, DC/DC's in SMT Packages
Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000
www.murata-ps.com
MDC_LSM10A-D5.B01 Page 5 of 13
相关PDF资料 |
PDF描述 |
|---|---|
| LSM-2/10-D5-C | 1-OUTPUT 20 W DC-DC REG PWR SUPPLY MODULE |
| LSP3171MSAD | SWITCHING REGULATOR, 470 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT1009CPWG4 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
| LT1009IPWG4 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
| LT140SAB | SPECIALTY ANALOG CIRCUIT, PDSO4 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LSM-1 | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:Single Output, Non-Isolated, 3.3VIN, 0.8-2.5VOUT 10 Amp DC/DC’s in SMT Packages |
| LSM-1.2 | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:Single Output, Non-Isolated, 3.3VIN, 0.8-2.5VOUT 10 Amp DC/DC’s in SMT Packages |
| LSM-1.2/10-D12 | 制造商:Murata Power Solutions 功能描述:DC/DC SM 10A 10-14V IN,1.2V OUT, NON-ISO - Tape and Reel 制造商:Murata Power Solutions 功能描述:Module DC-DC 1-OUT 1.2V 10A 6-Pin SMT |
| LSM-1.2/10-D12-C | 功能描述:DC/DC转换器 12W 12V to 1.2V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LSM-1.2/10-D12EB | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:10 Amp DC/DC Power Converter Evaluation Boards |
发布紧急采购，3分钟左右您将得到回复。