- 您现在的位置：买卖IC网 > PDF目录44966 > LSM-1/10-D12-C (MURATA POWER SOLUTIONS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | LSM-1/10-D12-C |
| 厂商： | MURATA POWER SOLUTIONS INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, SMT-6 |
| 文件页数： | 15/18页 |
| 文件大小： | 1583K |
| 代理商： | LSM-1/10-D12-C |
MDC_LSM 10A D12 Models.B01 Page 6 of 18
Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000
www.murata-ps.com
Single Output
LSM-10A D12 Models
Non-Isolated, 12Vin, 0.75-5Vout DC/DC Converters
External Input Open: On/Off pin Low = DC/DC converter Off
External Input Low: On/Off pin High = DC/DC converter On
Figure 5. Driving the External Power-Up Open Collector
Figure 4A. LSM-T10-D12 Driving the On/Off Control Input
ON/OFF pin open: Logic High = DC/DC converter On
ON/OFF pin <0.4V: Logic Low = DC/DC converter Off
Figure 4. Driving the On/Off Control Pin with an Open-Collector Drive Circuit
(All models except LSM-T/10-D12)
The sense function is capable of compensating for voltage drops between
the +Output and +Sense pins that do not exceed 10% of VOUT.
[VOUT(+) – Common] – [Sense(+) – Common]
≤ 10%VOUT
Power derating (output current limiting) is based upon maximum output cur-
rent and voltage at the converter's output pins. Use of trim and sense functions
can cause the output voltage to increase, thereby increasing output power
beyond the LSM's specified rating. Therefore:
(VOUT at pins) x (IOUT)
≤ rated output power
The internal 10.5
resistor between +Sense and +Output (see Figure 1)
serves to protect the sense function by limiting the output current flowing
through the sense line if the main output is disconnected. It also prevents
output voltage runaway if the sense connection is disconnected.
Note: If the sense function is not used for remote regulation, +Sense
(pin 6) must be tied to +Output (pin 4) at the DC/DC converter pins.
On/Off Control
The On/Off Control pin may be used for remote on/off operation. LSM D12
Series DC/DC converters are designed so that they are enabled when the con-
trol pin is left open (open collector) and disabled when the control pin is pulled
low (to less than +0.4V relative to Common). As shown in Figure 4, all models
have an internal pull-up resistor.
Dynamic control of the on/off function is best accomplished with a
mechanical relay or open-collector/open-drain drive circuit (optically isolated if
appropriate). The drive circuit should be able to sink appropriate current when
activated and withstand appropriate voltage when deactivated.
Applying an external voltage to the On/Off Control pin when no input power
is applied to the converter can cause permanent damage to the converter. The
on/off control function, however, is designed such that the converter can be
disabled (control pin pulled low) while input voltage is ramping up and then
"released" once the input has stabilized (see also power-up sequencing).
Power-up Sequencing
If a controlled start-up of one or more LSM D12 Series DC/DC converters
is required, or if several output voltages need to be powered-up in a given
sequence, the On/Off control pin can be driven with an external open collector
device as per Figure 5.
Leaving the input of the external circuit open during power-up will have the
output of the DC/DC converter disabled. When the input to the external open
collector is pulled low, the DC/DC converters output will be enabled.
Output Overvoltage Protection
LSM D12 SMT Series DC/DC converters do not incorporate output overvoltage
protection. In the extremely rare situation in which the device’s feedback loop
is broken, the output voltage may run to excessively high levels (VOUT = VIN). If it
is absolutely imperative that you protect your load against any and all possible
overvoltage situations, voltage limiting circuitry must be provided external to
the power converter.
Output Overcurrent Detection
Overloading the power converter's output for an extended time will invariably
cause internal component temperatures to exceed their maximum ratings and
eventually lead to component failure. High-current-carrying components such
as inductors, FET's and diodes are at the highest risk. LSM D12 SMT Series
DC/DC converters incorporate an output overcurrent detection and shutdown
function that serves to protect both the power converter and its load.
相关PDF资料 |
PDF描述 |
|---|---|
| LSM-1.2/10-D12-C | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSM-T/10-D12 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSM-T/10-D12-C | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSM-1.8/10-D12-C | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSM-1.5/16-W3-C | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LSM115J | 功能描述:DIODE SCHOTTKY 1A 15V DO214BA RoHS:否 类别:分离式半导体产品 >> 单二极管/整流器 系列:- 标准包装:100 系列:- 二极管类型:标准 电压 - (Vr)（最大）:50V 电流 - 平均整流 (Io):6A 电压 - 在 If 时为正向 (Vf)（最大）:1.4V @ 6A 速度:快速恢复 = 200mA（Io） 反向恢复时间(trr):300ns 电流 - 在 Vr 时反向漏电:15µA @ 50V 电容@ Vr, F:- 安装类型:底座，接线柱安装 封装/外壳:DO-203AA，DO-4，接线柱 供应商设备封装:DO-203AA 包装:散装 其它名称:*1N3879 |
| LSM115JE3/TR13 | 功能描述:DIODE SCHOTTKY 1A 15V DO214BA RoHS:是 类别:分离式半导体产品 >> 单二极管/整流器 系列:- 标准包装:100 系列:- 二极管类型:标准 电压 - (Vr)（最大）:50V 电流 - 平均整流 (Io):6A 电压 - 在 If 时为正向 (Vf)（最大）:1.4V @ 6A 速度:快速恢复 = 200mA（Io） 反向恢复时间(trr):300ns 电流 - 在 Vr 时反向漏电:15µA @ 50V 电容@ Vr, F:- 安装类型:底座，接线柱安装 封装/外壳:DO-203AA，DO-4，接线柱 供应商设备封装:DO-203AA 包装:散装 其它名称:*1N3879 |
| LSM115JTR7 | 制造商:Microsemi Corporation 功能描述: |
| LSM-11D | 制造商:EATON MOELLER 功能描述:BASIC UNIT METAL 1EARLY BR IP66 |
| LSM-11S | 制造商:Eaton 功能描述:Bulk 制造商:EATON MOELLER 功能描述:BASIC UNIT METAL 1NO/1NC IP66 |
发布紧急采购，3分钟左右您将得到回复。