- 您现在的位置：买卖IC网 > PDF目录79923 > LSM-5/10-D12 (CD TECHNOLOGIES INC) 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | LSM-5/10-D12 |
| 厂商： | CD TECHNOLOGIES INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | SMT-6 |
| 文件页数： | 8/13页 |
| 文件大小： | 660K |
| 代理商： | LSM-5/10-D12 |
LSM-10A D12 Series
N O N - I S O L A T E D , 8 - 5 0 W S M T D C / D C C O N V E R T E R S
The most effective combination of external I/O capacitors will be a function
of your line voltage and source impedance, as well as your particular load and
layout conditions. Our Applications Engineers can recommend potential solu-
tions and discuss the possibility of our modifying a given device’s internal lter-
ing to meet your specic requirements. Contact our Applications Engineering
Group for additional details.
Input Fusing
Most applications and or safety agencies require the installation of fuses
at the inputs of power conversion components. LSM D12 Series DC/DC
converters are not internally fused. Therefore, if input fusing is mandatory,
either a normal-blow or a fast-blow fuse with a value no greater than 20 Amps
should be installed within the ungrounded input path to the converter.
As a rule of thumb however, we recommend to use a normal-blow or slow-
blow fuse with a typical value of about twice the maximum input current,
calculated at low line with the converters minimum efciency.
Safety Considerations
LSM D12 SMT's are non-isolated DC/DC converters. In general, all DC/DC's
must be installed, including considerations for I/O voltages and spacing/
separation requirements, in compliance with relevant safety-agency speci-
cations (usually UL/IEC/EN60950).
In particular, for a non-isolated converter's output voltage to meet SELV
(safety extra low voltage) requirements, its input must be SELV compliant.
If the output needs to be ELV (extra low voltage), the input must be ELV.
4
Input Overvoltage and Reverse-Polarity Protection
LSM D12 SMT Series DC/DC's do not incorporate either input overvoltage
or input reverse-polarity protection. Input voltages in excess of the specied
absolute maximum ratings and input polarity reversals of longer than "instan-
taneous" duration can cause permanent damage to these devices.
Start-Up Time
The VIN to VOUT Start-Up Time is the interval between the time at which a
ramping input voltage crosses the lower limit of the specied input voltage
range (10.8 Volts) and the fully loaded output voltage enters and remains
within its specied accuracy band. Actual measured times will vary with input
source impedance, external input capacitance, and the slew rate and nal
value of the input voltage as it appears to the converter.
The On/Off to VOUT Start-Up Time assumes the converter is turned off via the
On/Off Control with the nominal input voltage already applied to the converter.
The specication denes the interval between the time at which the converter
is turned on and the fully loaded output voltage enters and remains within its
specied accuracy band. See Typical Performance Curves.
Figure 3. Measuring Output Ripple/Noise (PARD)
Remote Sense
LSM D12 SMT Series DC/DC converters offer an output sense function on
pin 6. The sense function enables point-of-use regulation for overcoming
moderate IR drops in conductors and/or cabling. Since these are non-isolated
devices whose inputs and outputs usually share the same ground plane,
sense is provided only for the +Output.
The remote sense line is part of the feedback control loop regulating the
DC/DC converter’s output. The sense line carries very little current and
consequently requires a minimal cross-sectional-area conductor. As such, it
is not a low-impedance point and must be treated with care in layout and
cabling. Sense lines should be run adjacent to signals (preferably ground),
and in cable and/or discrete-wiring applications, twisted-pair or similar tech-
niques should be used. To prevent high frequency voltage differences between
VOUT and Sense, we recommend installation of a 1000pF capacitor close to
the converter.
The sense function is capable of compensating for voltage drops between the
+Output and +Sense pins that do not exceed 10% of VOUT.
[VOUT(+) – Common] – [Sense(+) – Common]
≤ 10%VOUT
Power derating (output current limiting) is based upon maximum output cur-
rent and voltage at the converter's output pins. Use of trim and sense func-
tions can cause the output voltage to increase, thereby increasing output
power beyond the LSM's specied rating. Therefore:
(VOUT at pins) x (IOUT)
≤ rated output power
The internal 10.5
resistor between +Sense and +Output (see Figure 1)
serves to protect the sense function by limiting the output current owing
through the sense line if the main output is disconnected. It also prevents
output voltage runaway if the sense connection is disconnected.
Note: If the sense function is not used for remote regulation, +Sense
(pin 6) must be tied to +Output (pin 4) at the DC/DC converter pins.
Output ripple/noise (also referred to as periodic and random deviations
or PARD) may be reduced below specied limits with the installation of
additional external output capacitors. Output capacitors function as true lter
elements and should be selected for bulk capacitance, low ESR, and appro-
priate frequency response. Any scope measurements of PARD should be
made directly at the DC/DC output pins with scope probe ground less than
0.5" in length.
C1
C1 = NA
C2 = 22F TANTALUM
LOAD 2-3 INCHES (51-76mm) FROM MODULE
C2
RLOAD
6
4
COPPER STRIP
3
COPPER STRIP
SCOPE
+OUTPUT
COMMON
+SENSE
All external capacitors should have appropriate voltage ratings and be located
as close to the converters as possible. Temperature variations for all relevant
parameters should be taken into consideration.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC6992CDCB-4#TRMPBF | 0.02 A SWITCHING CONTROLLER, PDSO6 |
| LMH6581VS/NOPB | 8-CHANNEL, CROSS POINT SWITCH, PQFP48 |
| LM2670LDX-5.0 | 5.4 A SWITCHING REGULATOR, 280 kHz SWITCHING FREQ-MAX, PDSO14 |
| LM336B-5.0MDC | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 5 V, UUC |
| LSM-1.2/10-D12 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LSM535 | 制造商:MICROSEMI 制造商全称:Microsemi Corporation 功能描述:5 Amp Schottky Rectifier |
| LSM535G | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Schottky Rectifier |
| LSM535G/TR13 | 制造商:Microsemi Corporation 功能描述:5.0A, 35V, VF=0.52V - Tape and Reel 制造商:Microsemi Corporation 功能描述:DIODE SCHOTTKY 5A 35V SMCG |
| LSM535GE3/TR13 | 制造商:Microsemi Corporation 功能描述:5.0A, 35V, VF=0.52V - Tape and Reel 制造商:Microsemi Corporation 功能描述:DIODE SCHOTTKY 5A 35V SMCG |
| LSM535J | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Schottky Rectifier |
发布紧急采购，3分钟左右您将得到回复。