- 您现在的位置：买卖IC网 > PDF目录44968 > LSM330DL (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA28 PDF资料下载
参数资料
| 型号： | LSM330DL |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA28 |
| 封装： | 7.50 X 4.40 MM, 1.10 MM HEIGHT, GREEN, PLASTIC, LGA-28 |
| 文件页数： | 29/54页 |
| 文件大小： | 1064K |
| 代理商： | LSM330DL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
LSM330DL
Registers description
Doc ID 022018 Rev 1
35/54
The contents of the INT1_CFG_REG_A register are loaded at boot.
A write operation at this address is possible only after system boot.
The difference between AOI-6D = ‘01’ and AOI-6D = ‘11’ is defined as follows:
AOI-6D = ‘01’ is movement recognition. An interrupt is generated when the orientation
moves from an unknown zone to a known zone. The interrupt signal stays for a duration
determined by ODR.
AOI-6D = ‘11’ is direction recognition. An interrupt is generated when the orientation is
inside a known zone. The interrupt signal stays until orientation is inside the zone.
7.15
INT1_SRC_A (31h)
XHIE/
XUPE
Enable interrupt generation on X high event or on direction recognition. Default value: 0
(0: disable interrupt request; 1: enable interrupt request.)
XLIE/XDO
WNE
Enable interrupt generation on X low event or on direction recognition. Default value: 0
(0: disable interrupt request; 1: enable interrupt request.)
Table 44.
Interrupt mode
AOI
6D
Interrupt mode
0
OR combination of interrupt events
0
1
6-direction movement recognition
1
0
AND combination of interrupt events
11
6-direction position recognition
Table 43.
INT1_CFG_REG_A description (continued)
Table 45.
INT1_SRC_A register
0(1)
1.
This bit has to be set to ‘0’ for correct operation.
IA
ZH
ZL
YH
YL
XH
XL
Table 46.
INT1_SRC_A description
IA
Interrupt active. Default value: 0
(0: no interrupt has been generated; 1: one or more interrupts have been generated)
ZH
Z high. Default value: 0
(0: no interrupt, 1: Z high event has occurred)
ZL
Z low. Default value: 0
(0: no interrupt; 1: Z low event has occurred)
YH
Y high. Default value: 0
(0: no interrupt, 1: Y high event has occurred)
YL
Y low. Default value: 0
(0: no interrupt, 1: Y low event has occurred)
相关PDF资料 |
PDF描述 |
|---|---|
| LSN-0.75/16-D12HJ-C | 1-OUTPUT 12.8 W DC-DC REG PWR SUPPLY MODULE |
| LSN-1.8/16-D12HJ-C | 1-OUTPUT 28.8 W DC-DC REG PWR SUPPLY MODULE |
| LSN-1.2/16-D12HJ-C | 1-OUTPUT 19.2 W DC-DC REG PWR SUPPLY MODULE |
| LSN-2.5/16-D12HJ-C | 1-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE |
| LSN-1/16-D12HJ-C | 1-OUTPUT 16 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LSM330DLC | 功能描述:加速计 - 板上安装 iNEMO 3D SIP Module 2.4V to 3.6V IO 1.8V RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LSM330DLCTR | 功能描述:加速计 - 板上安装 iNEMO 3D SIP Module 2.4V to 3.6V IO 1.8V RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LSM330DLTR | 功能描述:加速计 - 板上安装 Linear Sensor Module 3D ACC 3D Gyro RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LSM330DTR | 制造商:STMicroelectronics 功能描述:INEMO INERTIAL MODULE: 3D ACCELEROMETER AND 3D GYROSCOPE |
| LSM330TR | 功能描述:加速计 - 板上安装 Inemo inertial module 3D accelerometer and 3D gyroscope RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
发布紧急采购，3分钟左右您将得到回复。