- 您现在的位置：买卖IC网 > PDF目录79879 > LSN-1.2/10-D3H (CD TECHNOLOGIES INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | LSN-1.2/10-D3H |
| 厂商： | CD TECHNOLOGIES INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封装： | SIP-11/10 |
| 文件页数： | 10/14页 |
| 文件大小： | 528K |
| 代理商： | LSN-1.2/10-D3H |
LSN-10A D3 Models
N O N - I S O L A T E D , 1 0 - 2 5 W S I P D C / D C C O N V E R T E R S
Figure 3.Trim Connections Using a Trimpot
LSN-1/10-D3 Trim Equations
LSN-1.2/10-D3, LSN-1.25/10-D3 Trim Equations
Note: Resistor values are in k
. Accuracy of adjustment is subject to
tolerances of resistors and factory-adjusted, initial output accuracy.
VO = desired output voltage. VO
NOM = nominal output voltage.
5
LSN-1.5/10-D3, LSN-1.8/10-D3,
LSN-2/10-D3, LSN-2.5/10-D3 Trim Equations
Figure 4.Trim Connections Using Fixed Resistors
Note: Install either a xed trim-up resistor or a xed trim-down resistor
depending upon desired output voltage.
Trim
Down
Trim Up
LOAD
+INPUT
COMMON
+OUTPUT
TRIM
COMMON
Output Reverse Conduction
Many DC/DC converters using synchronous rectication suffer from Output
Reverse Conduction. If those devices have a voltage applied across their
output before a voltage is applied to their input (this typically occurs when
another power supply starts before them in a power-sequenced application),
Output Voltage Trimming
Allowable trim ranges for each model in the LSN D3 SIP Series are ±10%.
Trimming is accomplished with either a trimpot or a single xed resistor. The
trimpot should be connected between +Output and Common with its wiper
connected to the Trim pin as shown in Figure 3 below.
A trimpot can be used to determine the value of a single xed resistor
which can then be connected, as shown in Figure 4, between the Trim pin
and +Output to trim down the output voltage, or between the Trim pin and
Common to trim up the output voltage. Fixed resistors should have absolute
TCR’s less than 100ppm/°C to ensure stability.
Output Overvoltage Protection
LSN D3 SIP Series DC/DC converters do not incorporate output overvoltage
protection. In the extremely rare situation in which the device’s feedback loop
is broken, the output voltage may run to excessively high levels (VOUT = VIN).
If it is absolutely imperative that you protect your load against any and all
possible overvoltage situations, voltage limiting circuitry must be provided
external to the power converter.
Output Overcurrent Detection
Overloading the output of a power converter for an extended period of
time will invariably cause internal component temperatures to exceed their
maximum ratings and eventually lead to component failure. High-current-
carrying components such as inductors, FET's and diodes are at the highest
risk. LSN D3 SIP Series DC/DC converters incorporate an output overcurrent
detection and shutdown function that serves to protect both the power
converter and its load.
If the output current exceeds it maximum rating by typically 60% (16 Amps) or
if the output voltage drops to less than 98% of it original value, the LSN D3's
internal overcurrent-detection circuitry immediately turns off the converter,
which then goes into a "hiccup" mode. While hiccupping, the converter will
continuously attempt to restart itself, go into overcurrent, and then shut down.
Under these conditions, the average output current will be approximately
400mA, and the average input current will be approximately 70mA. Once the
output short is removed, the converter will automatically restart itself.
Figure 2a. Inverting On/Off Control Pin Signal and Power-Up Sequencing
+INPUT
COMMON
5k
1.1k
0.9k
0.75k
ON/OFF
CONTROL
For a controlled start-up of one or more LSN-D3's, or if several output volt-
ages need to be powered-up in a given sequence, the On/Off Control pin can
be pulled high (external pull-up resistor, converter disabled) and then driven
low with an external open collector device to enable the converter.
The equations below can be used as starting points for selecting specic trim-
resistor values. Recall, untrimmed devices are guaranteed to be ±1% accurate.
Adjustment beyond the specied ±10% adjustment range is not recommended.
相关PDF资料 |
PDF描述 |
|---|---|
| LM3420AM5-8.2/NOPB | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| LM1575K-5.0/883 | 1.3 A SWITCHING REGULATOR, 52 kHz SWITCHING FREQ-MAX, MBFM4 |
| LS4601-7EPD4T | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LH2320-2D3 | 2-OUTPUT AC-DC UNREG PWR SUPPLY MODULE |
| LK2660-7EPD9TB1 | 2-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LSN1210D5 | 制造商:Datel 功能描述: |
| LSN1210D5C | 制造商:Datel 功能描述: |
| LSN1510D12J | 制造商:Datel 功能描述: |
| LSN1510D5 | 制造商:Datel 功能描述: |
| LSN16A-D12 | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:Single Output, Non-Isolated, 12VIN, 0.75-5VOUT 16 Amp in DC/DCs SIP Packages |
发布紧急采购，3分钟左右您将得到回复。