参数资料
型号: LSN-1.2/10-D5BH
厂商: CD TECHNOLOGIES INC
元件分类: 电源模块
英文描述: 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
封装: SIP-9
文件页数: 8/11页
文件大小: 361K
代理商: LSN-1.2/10-D5BH
LSN-10A D5 Series
N O N - I S O L A T E D , 1 0 - 3 3 W S I P D C / D C C O N V E R T E R S
–40
0
60
70
80
90
100
110
LSN-1/10-D5
Output Current vs. Ambient Temperature
(Vertical mount, air flow direction from pin 1 to pin 11)
Output
Current
(Amps)
Ambient Temperature (
°C)
10
8
6
4
2
0
Natural Convection
200 lfm
100 lfm
LSN-1.5/10-D5
Output Current vs. Ambient Temperature
(Vertical mount, air flow direction from pin 1 to pin 11)
Output
Current
(Amps)
Ambient Temperature (
°C)
10
8
6
4
2
0
Natural Convection
200 lfm
100 lfm
–40
0
60
70
80
90
100
110
LSN-1.8/10-D5 & LSN-2/10-D5
Output Current vs. Ambient Temperature
(Vertical mount, air flow direction from pin 1 to pin 11)
Output
Current
(Amps)
Ambient Temperature (
°C)
10
8
6
4
2
0
Natural Convection
200 lfm
100 lfm
–40
0
60
70
80
90
100
110
–40
0
60
70
80
90
100
110
LSN-1.2/10-D5
Output Current vs. Ambient Temperature
(Vertical mount, air flow direction from pin 1 to pin 11)
Output
Current
(Amps)
Ambient Temperature (
°C)
10
8
6
4
2
0
Natural Convection
200 lfm
100 lfm
Typical Performance Curves for LSN D5 SIP Series
6
Thermal Considerations and Thermal Protection
The typical output-current thermal-derating curves shown below enable
designers to determine how much current they can reliably derive from each
model of the LSN D5 SIP's under known ambient-temperature and air-ow
conditions. Similarly, the curves indicate how much air ow is required to
reliably deliver a required output current at known temperatures.
The highest temperatures in LSN D5 SIP's occur at their output inductor,
whose heat is generated primarily by I2R losses. The above curves were
developed using thermocouples to monitor the inductor temperature and
varying the load to keep that temperature below +110°C under the assorted
conditions of air ow and air temperature. Once the temperature exceeds
+115°C (approx.), the thermal protection will disable the converter. Automatic
restart occurs after the temperature has dropped below +110°C.
In all cases below, the DUT's were vertical-mount models, and the direction
of air ow was parallel to the unit in the direction from pin 1 to pin 11.
As you may deduce from the above curves and can observe in the efciency
curves on the next page, LSN D5 SIP's are more efcient at lower current
levels. Also, I2R losses in the output inductor are signicantly less at lower
currents. Consequently, LSN D5 SIP's deliver very impressive temperature
performance if operating at less than full load.
Lastly, when LSN D5 SIP's are installed in system boards, they are obviously
subject to numerous factors and tolerances not taken into account above.
If you are attempting to extract the most current out of these units under
demanding temperature conditions, we advise you to monitor the output-
inductor temperature to ensure it remains below +110°C at all times.
Thermal Performance for "H" Models
Enhanced thermal performance can be achieved when LSN D5 SIP's are
mounted horizontally ("H" models) and the output inductor (with its electrically
isolating, thermally conductive pad installed) is thermally coupled to a copper
plane/pad (at least 0.55 square inches in area) on the system board.Your
conditions may vary, however our tests indicate this conguration delivers a
16°C to 22°C improvement in ambient operating temperatures.
they will either fail to start or self destruct. In both cases, the cause is the
"freewheeling" or "catch" FET biasing itself on and effectively becoming a
short circuit.
LSN D5 SIP DC/DC converters are not damaged from Output Reverse
Conduction. They employ proprietary gate drive circuitry which makes them
immune to applied voltages during the startup sequence. If you are using
an external power source paralleled with the LSN, be aware that during the
start up phase, some low impedance condition or transient current may be
absorbed briey into the LSN output terminals before voltage regulation is
fully established.You should insure that paralleled external power sources are
not disrupted by this condition during LSN start up.
相关PDF资料
PDF描述
LSN-1/10-D5H 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE
LSN-2.5/10-D5J 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
LSN-1.8/10-D5B 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
LSN-2/10-D5B 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
LSN-3.3/10-D5J 1-OUTPUT 33 W DC-DC REG PWR SUPPLY MODULE
相关代理商/技术参数
参数描述
LSN1210D5C 制造商:Datel 功能描述:
LSN1510D12J 制造商:Datel 功能描述:
LSN1510D5 制造商:Datel 功能描述:
LSN16A-D12 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:Single Output, Non-Isolated, 12VIN, 0.75-5VOUT 16 Amp in DC/DCs SIP Packages
LSN16A-W3 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:Non-Isolated, 3-5.5VIN, 0.75-3.3VOUT 16 Amp DC/DC Converters