- 您现在的位置：买卖IC网 > PDF目录44976 > LSN2-T/16-W3NGC (MURATA POWER SOLUTIONS INC) 1-OUTPUT 52.8 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | LSN2-T/16-W3NGC |
| 厂商： | MURATA POWER SOLUTIONS INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 52.8 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, SIP-12 |
| 文件页数： | 13/15页 |
| 文件大小： | 302K |
| 代理商： | LSN2-T/16-W3NGC |
LSN2 Series
Non-isolated, DOSA-SIP, 6/10/16A
Selectable-Output DC/DC Converters
www.murata-ps.com
email: sales@murata-ps.com
25 Jun 2010
MDC_LSN2.B07Δ Page 7 of 15
Figure 5. Inverting On/Off Control
Output Overcurrent Detection
Overloading the power converter's output for an extended time will invariably
cause internal component temperatures to exceed their maximum ratings and
eventually lead to component failure. High-current-carrying components such
as inductors, FET's and diodes are at the highest risk. LSN2 SIP Series DC/DC
converters incorporate an output overcurrent detection and shutdown function
that serves to protect both the power converter and its load.
If the output current exceeds it maximum rating by typically 50% or if the
output voltage drops to less than 98% of it original value, the LSN2's internal
overcurrent-detection circuitry immediately turns off the converter, which then
goes into a “hiccup” mode. While hiccupping, the converter will continuously
attempt to restart itself, go into overcurrent, and then shut down. Once the
output short is removed, the converter will automatically restart itself.
Output Reverse Conduction
Many DC/DCs using synchronous rectication suffer from Output Reverse
Conduction. If those devices have a voltage applied across their output before
a voltage is applied to their input (this typically occurs when another power
supply starts before them in a power-sequenced application), they will either
fail to start or self destruct. In both cases, the cause is the “freewheeling” or
“catch” FET biasing itself on and effectively becoming a short circuit.
LSN2 SIP DC/DC converters do not suffer from Output Reverse Conduction.
They employ proprietary gate drive circuitry that makes them immune to
moderate applied output overvoltages.
Thermal Considerations and Thermal Protection
The typical output-current thermal-derating curves shown below enable
designers to determine how much current they can reliably derive from each
model of the LSN2 SIPs under known ambient-temperature and air-ow con-
ditions. Similarly, the curves indicate how much air ow is required to reliably
deliver a specic output current at known temperatures.
through the sense line if the main output is disconnected. It also prevents
output voltage runaway if the sense connection is disconnected.
Note: If the sense function is not used for remote regulation, +Sense
must be tied to +Output at the DC/DC converter pins.
Remote On/Off Control
The input-side remote On/Off Control is an external input signal available in
either positive (no sufx) or negative (“N” sufx) polarity. Normally this input
is controlled by the user’s external transistor or relay. With simple external
circuits, it may also be selected by logic outputs. Please note however that
the actual control threshold levels vary somewhat with the PWM supply and
therefore are best suited to “open collector” or “open drain” type logic. The
On/Off control takes effect only when appropriate input power has been ap-
plied and stabilized (approximately 7msec).
For positive polarity, the default operation leaves this pin open (unconnected)
or HIGH. The output will then always be on (enabled) whenever appropriate
input power is applied. Negative polarity models require the On/Off to be
grounded to the –Input terminal or brought LOW to turn the converter on.
To turn the converter off, for positive polarity models, ground the On/Off
control or bring it LOW. For negative polarity, raise the On/Off at least to +2.5V
to turn it off.
Dynamic control of the On/Off must be capable of sinking or sourcing the
control current (approximately 1mA max.) and not overdrive the input greater
than the +VIN power input. Always wait for the input power to stabilize before
activating the On/Off control. Be aware that a delay of several milliseconds
occurs (see specications) between activation of the control and the resulting
change in the output.
Power-up sequencing
If a controlled start-up of one or more LSN2 Series DC/DC converters is required,
or if several output voltages need to be powered-up in a given sequence, the
On/Off control pin can be driven with an external open collector device as per
Figure 4.
Output Overvoltage Protection
LSN2 SIP Series DC/DC converters do not incorporate output overvoltage pro-
tection. In the extremely rare situation in which the device’s feedback loop is
broken, the output voltage may run to excessively high levels (VOUT = VIN). If it
is absolutely imperative that you protect your load against any and all possible
overvoltage situations, voltage limiting circuitry must be provided external to
the power converter.
Figure 4. On/Off Control Using An External Open Collector Driver
Leaving the input of the on/off circuit closed during power-up will have the
output of the DC/DC converter disabled. When the input to the external open
collector is pulled high, the DC/DC converter’s output will be enabled.
相关PDF资料 |
PDF描述 |
|---|---|
| LSN2-T/6-W3NG-C | 1-OUTPUT 19.8 W DC-DC REG PWR SUPPLY MODULE |
| LSN2-T/10-W3GC | 1-OUTPUT 33 W DC-DC REG PWR SUPPLY MODULE |
| LSN2-T/16-D12G-C | 1-OUTPUT 80 W DC-DC REG PWR SUPPLY MODULE |
| LSN2-T/6-D12GC | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| LSN2-T/6-W3GC | 1-OUTPUT 19.8 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LSN2-T30-D12 | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:DOSA-SIP, 30A POL DC/DC Converters |
| LSN2-T30-D12-C | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:DOSA-SIP, 30A POL DC/DC Converters |
| LSN2-T30-D12G-C | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:DOSA-SIP, 30A POL DC/DC Converters |
| LSN-3.3/10-D12 | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LSN-3.3/10-D12B | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。