- 您现在的位置：买卖IC网 > PDF目录44976 > LSN2-T/6-D12GC (MURATA POWER SOLUTIONS INC) 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | LSN2-T/6-D12GC |
| 厂商： | MURATA POWER SOLUTIONS INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, SIP-7 |
| 文件页数： | 2/15页 |
| 文件大小： | 302K |
| 代理商： | LSN2-T/6-D12GC |
LSN2 Series
Non-isolated, DOSA-SIP, 6/10/16A
Selectable-Output DC/DC Converters
www.murata-ps.com
email: sales@murata-ps.com
25 Jun 2010
MDC_LSN2.B07Δ Page 10 of 15
Timing is Everything
This mix of system voltages is being distributed by several local power solu-
tions including Point-of-load (POL) DC/DC converters and sometimes a linear
regulator, all sourced from a master AC power supply. While this mix of volt-
ages is challenging enough, a further difculty is the start-up and shutdown
timing relationship between these power sources and relative voltage differ-
ences between them.
For many systems, the CPU and memory must be powered up, boot-
strap loaded and stabilized before the I/O section is turned on. This avoids
uncommanded data bytes being transferred, compromising an active external
network or placing the I/O section in an undened mode. Or it keeps bad com-
mands out of disk and peripheral controllers until they are ready to go to work.
Another goal for staggered power-up is to avoid an oversize load applied
to the master source all at once. A more serious reason to manage the timing
and voltage differences is to avoid either a latchup condition in program-
mable logic (a latchup might ignore commands or would respond improperly
to them) or a high current startup situation (which may damage on-board
circuits). And on the power down phase, inappropriate timing or voltages can
cause interface logic to send a wrong “epitaph” command.
Two Approaches
There are two ways to manage these timing and voltage differences. Either
the power up/down sequence can be controlled by discrete On/Off logic con-
trols for each power supply (see Figure 7). Or the power up/down cycle is set
by Sequencing or Tracking circuits. Some systems combine both methods.
The rst system (discrete On/Off controls) applies signals from an already-
powered logic sequencer or dedicated microcontroller which turns on each
downstream power section in cascaded series. This of course assumes all
POL’s have On/Off controls. A distinct advantage of the sequencing controller
is that it can produce an “All On” output signal to state that the full system is
stable and ready to go to work. For additional safety, the sequencer can moni-
tor the output voltages of all downstream POL’s with an A/D converter system.
However the sequencer controller has some obvious difculties besides
extra cost, wiring and programming complexity. First, power is applied as a
fast-rising, all-or-nothing step which may be unacceptable to certain circuits,
especially large output bypass capacitors. These could force POL’s into
overcurrent shutdown. And some circuits (such as many linear regulators and
some POLs) may not have convenient start-up controls. This requires design-
ing and fabricating external power controls such as high-current MOSFET’s.
If the power up/down timing needs to be closely controlled, each POL
must be characterized for start-up and down times. These often vary—one
POL may stabilize in 15 milliseconds whereas another takes 50 milliseconds.
Another problem is that the sequencing controller itself must be “already
running” and stabilized before starting up other circuits. If there is a glitch in
the system, the power up/down sequencer could get out of step with possible
disastrous results. Lastly, changing the timing may require reprogramming the
logic sequencer or rewriting software.
Sequence/Track Input
A different power sequencing solution is employed on MPS’s LSN2 DC/DC
converter. After external input power is applied and the converter stabilizes,
a high impedance Sequence/Track input pin accepts an external analog volt-
age. The output power voltage will then track this Sequence/Track input at a
one-to-one ratio up to the nominal set point voltage for that converter. This
Sequencing input may be ramped, delayed, stepped or otherwise phased as
needed for the output power, all fully controlled by the user’s simple external
circuits. As a direct input to the converter’s feedback loop, response to the
Sequence/Track input is very fast (milliseconds).
By properly controlling this Sequence pin, most operations of the discrete
On/Off logic sequencer may be duplicated. The Sequence pin system does
not use the converter’s Enable On/Off control (unless it is a master emergency
shut down system).
Power Phasing Architectures
Observe the simplied timing diagrams below. There are many possible power
phasing architectures and these are just some examples to help you analyze
your system. Each application will be different. Multiple output voltages may
require more complex timing than that shown here.
These diagrams illustrate the time and slew rate relationship between two
typical power output voltages. Generally the Master will be a primary power
voltage in the system which must be present rst or coincident with any
Slave power voltages. The Master output voltage is connected to the Slave’s
Sequence input, either by a voltage divider, divider-plus-capacitor or some
SEQUENCING
CONTROLLER
ENABLE
+VIN
POL
A
“ALL ON”
POL
B
CPU
TO OTHER POLs
+5V
LOADS
+12Vdc
+3.3V
LOADS
ENABLE
TIME
Settling
Delay
POL A
ENABLE
STARTUP SEQUENCE:
OFF
ON
POL B
Figure 7. Power Up/Down Sequencing Controller
相关PDF资料 |
PDF描述 |
|---|---|
| LSN2-T/6-W3GC | 1-OUTPUT 19.8 W DC-DC REG PWR SUPPLY MODULE |
| LSN2-T/10-D12-C | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| LSN2-T/10-D12C | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| LSP3102QAD | 1.45 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, QCC16 |
| LSP3102Y12AD | 1.45 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LSN-3.3/10-D12 | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LSN-3.3/10-D12B | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LSN-3.3/10-D12B-C | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LSN-3.3/10-D12BH | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LSN-3.3/10-D12BH-C | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。