- 您现在的位置：买卖IC网 > PDF目录79923 > LSN2-T/6-D12N-C (CD TECHNOLOGIES INC) 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | LSN2-T/6-D12N-C |
| 厂商： | CD TECHNOLOGIES INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, SIP-12 |
| 文件页数： | 9/14页 |
| 文件大小： | 1441K |
| 代理商： | LSN2-T/6-D12N-C |
Figure 1. LSN2 Series Simplified Schematic
LSN2 Series
Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters
MDC_LSN2_A03 Page 4 of 14
D C / D C C O N V E R T E R S
Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000
www.murata-ps.com
Performance/Functional Specification Notes:
(1)
All models are tested and specified with external 1 || 10F ceramic/tantalum output capacitors
and a 22F external input capacitor. All capacitors are low ESR types. These capacitors are
necessary to accommodate our test equipment and may not be required to achieve specified
performance in your applications. All models are stable and regulate within spec under no-load
conditions.
General conditions for Specifications are +25°C, VIN = nominal, VOUT = nominal, full load. “Nomi-
nal” output voltage is +5V for D12 models and +3.3V for W3 models.
(2)
Input Back Ripple Current is tested and specified over a 5-20MHz bandwidth. Input filtering is
CIN = 2 x 100F tantalum, CBUS = 1000F electrolytic, LBUS = 1H.
(3)
Note that Maximum Power Derating curves indicate an average current at nominal input voltage.
At higher temperatures and/or lower airflow, the DC/DC converter will tolerate brief full current
outputs if the total RMS current over time does not exceed the derating curve.
(4)
Mean Time Before Failure is calculated using the Telcordia (Belcore) SR-332 Method 1, Case 3,
ground fixed conditions, TPCBOARD = +25°C, full output load, natural air convection.
(5)
The On/Off Control may be driven with external logic or by applying appropriate external voltages
which are referenced to –Input Common. The On/Off Control Input should use either an open
collector/open drain transistor or logic gate which does not exceed +VIN. A 68K
W external pullup
resistor to +VIN will cause the “ON” state for negative logic models.
(6)
Short circuit shutdown begins when the output voltage under increasing load degrades approxi-
mately 2% from the selected setting.
(7)
If Sense is connected remotely at the load, up to 0.5 Volts difference is allowed between the
Sense and +VOUT pins to compensate for ohmic voltage drop in the power lines. A larger voltage
drop may cause the converter to exceed maximum power dissipation.
I/O Filtering and Noise Reduction
All models in the LSN2 Series are tested and specified with external
1 || 10F ceramic/tantalum output capacitors and a 22F tantalum input
capacitor. These capacitors are necessary to accommodate our test equip-
ment and may not be required to achieve desired performance in your appli-
cation. The LSN2's are designed with high-quality, high-performance internal
I/O caps, and will operate within spec in most applications with no additional
external components.
In particular, the LSN2's input capacitors are specified for low ESR and are
fully rated to handle the units' input ripple currents. Similarly, the internal
output capacitors are specified for low ESR and full-range frequency response.
TECHNICAL NOTES
(8)
Output noise may be further reduced by adding an external filter. See I/O Filtering and Noise
Reduction.
(9)
All models are fully operational and meet published specifications, including “cold start” at
–40°C. VOUT is nominal.
(10)
Regulation specifications describe the deviation as the line input voltage or output load current is
varied from a nominal midpoint value to either extreme.
(11)
Other input or output voltage ranges are available under scheduled quantity special order.
(12)
Maximum PC board temperature is measured with the sensor in the center.
(13)
Do not exceed maximum power specifications when adjusting the output trim.
(14)
When Sequencing is not used, the Power Good output is TRUE at any time the output is within
approximately ±10% of the voltage set point. Power Good basically indicates if the converter is
in regulation. Power Good detects Over Temperature if the PWM has shut down due to OT. Power
Good does not directly detect Over Current.
If Sequencing is in progress, Power Good will falsely indicate TRUE (valid) before the output
reaches its setpoint. Ignore Power Good if Sequencing is in transition.
(15)
The maximum output capacitive loads depend on the the Equivalent Series Resistance (ESR) of
the external output capacitor.
(16)
Do not use Pre-bias startup and sequencing together. See Technical Notes below.
(17)
After short circuit shutdown, if the load is partially removed such that the load still exceeds the
overcurrent (OC) detection, the converter will remain in hiccup restart mode.
(18)
For best noise performance, leave the Track/Sequence pin OPEN when not used.
In critical applications, input/output ripple/noise may be further reduced using
filtering techniques, the simplest being the installation of external I/O caps.
External input capacitors serve primarily as energy-storage devices. They
minimize high-frequency variations in input voltage (usually caused by IR
drops in conductors leading to the DC/DC) as the switching converter draws
pulses of current. Input capacitors should be selected for bulk capacitance
(at appropriate frequencies), low ESR, and high rms-ripple-current ratings.
The switching nature of modern DC/DC's requires that the dc input voltage
source have low ac impedance at the frequencies of interest. Highly inductive
source impedances can greatly affect system stability. Your specific system
configuration may necessitate additional considerations.
Typical topology is shown
相关PDF资料 |
PDF描述 |
|---|---|
| LT1934IDCB-1#PBF | 0.49 A SWITCHING REGULATOR, PDSO6 |
| LSM-0.8/10-D3 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSN-1/10-D3H-C | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| LK4003-9RD6TB1 | 1-OUTPUT AC-DC PWR FACTOR CORR MODULE |
| LT4180EGN#PBF | POWER SUPPLY SUPPORT CKT, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LSN-3.3/10-D12 | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LSN-3.3/10-D12B | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LSN-3.3/10-D12B-C | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LSN-3.3/10-D12BH | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LSN-3.3/10-D12BH-C | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。