- 您现在的位置：买卖IC网 > PDF目录80228 > LSP3127SAE (LITE-ON SEMICONDUCTOR CORP) SWITCHING REGULATOR, PDSO8 PDF资料下载
参数资料
| 型号： | LSP3127SAE |
| 厂商： | LITE-ON SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, PDSO8 |
| 封装： | SOP-8 |
| 文件页数： | 6/8页 |
| 文件大小： | 135K |
| 代理商： | LSP3127SAE |
Liteon Semiconductor Corporation
LSP3127
52KHZ 2A PWM Buck DC/DC Converter
Rev1.1
6/8
Feedback
Senses the regulated output voltage to complete the feedback loop.
ON/OFF
Allows the switching regulator circuit to be shutdown using logic level signals thus dropping the total input
supply current to approximately 150uA. Pulling this pin below a threshold voltage of approximately 1.3V turns the
regulator on, and pulling this pin above 1.3V (up to a maximum of 25V) shuts the regulator down. If this
shutdown feature is not needed, the ON/OFF pin can be wired to the ground pin or it can be left open, in either
case the regulator will be in the ON condition.
Thermal Considerations
The SOP8L package needs a heat sink under most conditions. The size of the heatsink depends on the input
voltage, the output voltage, the load current and the ambient temperature. The LSP3127 junction temperature rises
above ambient temperature for a 2A load and different input and output voltages. The data for these curves was
taken with the LSP3127(SOP8L package) operating as a buck-switching regulator in an ambient temperature 25℃
(still air). These temperature increments are all approximate and are affected by many factors. Higher ambient
temperatures requires more heat sinker.
For the best thermal performance, wide copper traces and generous amounts of printed circuit board copper should
be used in the board layout. (One exception is the output (switch) pin, which should not have large areas of copper.)
Large areas of copper provide the best transfer of heat (lower thermal resistance) to the surrounding air, and moving
air lowers the thermal resistance even further.
Package thermal resistance and junction temperature increments are all approximate. The increments are affected
by a lot of factors. Some of these factors include board size, shape, thickness, position, location, and even board
temperature. Other factors are, trace width, total printed circuit copper area, copper thickness, single or
double-sided, multi-layer board and the amount of solder on the board.
The effectiveness of the PC board to dissipate heat also depends on the size, quantity and spacing of other
components on the board, as well as whether the surrounding air is still or moving. Furthermore, some of these
components such as the catch diode will add heat to the PC board and the heat can vary as the input voltage
changes. For the inductor, depending on the physical size, type of core material and the DC resistance, it could
either act as a heat sink taking heat away from the board, or it could add heat to the board.
ORDERING INFORMATION
相关PDF资料 |
PDF描述 |
|---|---|
| LTC6360IDD#PBF | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| LS1301-9EPDDTB1 | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LT1243MJ8 | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, CDIP8 |
| LT1019MS-4.5 | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 4.5 V, PDSO |
| LS1301-7RD3TB1 | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LSP32-K2-RGBA | 制造商:Dialight 功能描述:LED MODULE 32X K2 RGBA |
| LSP-32K2-RGBW | 制造商:Dialight 功能描述: |
| LSP32-K2-RGBW | 制造商:Dialight 功能描述:LED MODULE 32X K2 RGBW |
| LSP-32K2-WWWW | 制造商:Dialight 功能描述: |
| LSP32-K2-WWWW | 制造商:Dialight 功能描述:LED MODULE 32X K2 WWWW |
发布紧急采购，3分钟左右您将得到回复。