参数资料
| 型号： | LT1020ISW#TR |
| 厂商： | Linear Technology |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ 125MA 16SOIC |
| 标准包装： | 1,000 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 可调 |
| 输入电压： | 4.5 V ~ 36 V |
| 电压 - 压降（标准）： | 0.4V @ 125mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 125mA（最小） |
| 工作温度： | 0°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
LT1020
APPLICATIO S I FOR ATIO
than placing large capacitive loads on the reference, no
other precautions are necessary and the reference is
stable with nominal stray capacitances.
Like most other IC regulators, a minimum load is required
on the output of the LT1020 to maintain regulation. For
most standard regulators this is normally specified at
5mA. Of course, for a micropower regulator this would be
REF
REF
a tremendously large current. The output current must be
+
4
OUTPUT
20 ?
10 μ F
OR
+
4
20 ?
OUTPUT
10 μ F
large enough to absorb all the leakage current of the pass
transistor at the maximum operating temperature. It also
affects the transient response; low output currents have
long recovery times from load transients. At high operat-
1020 F01
Figure 1. Bypassing Reference
Overload Protection
The main regulator in the LT1020 is current limited at
approximately 350mA. The current limit is stable with both
input voltage and temperature. A current limit pin, when
strapped to ground, decreases the output current. This
allows the output current to be set to a lower value than
250mA. The output current available with the current limit
pin strapped to ground is not well controlled so if precise
current limiting is desired it should be provided externally
as is shown in some of the application circuits.
If the device is overloaded for long periods of time, thermal
shutdown turns the output off. In thermal shutdown, there
may be some oscillations which can disturb external
circuitry. A diode connected between the reference and
feedback terminal provides hysteresis under thermal shut-
down, so that the device turns on and off with about a 5
second period and there are no higher frequency oscilla-
tions. This is shown in Figure 2. This diode is recom-
mended for most applications. Thermal shutdown
temperature is set at approximately 145 ° C.
ing temperatures the minimum load current increases and
having too low of a load current may cause the output to
go unregulated. Devices are tested for minimum load
current at high temperature. The output voltage setting
resistors to the feedback terminal can usually be used to
provide the minimum load current.
Frequency Compensation
The LT1020 is frequency compensated by a dominant pole
on the output. An output capacitor of 10 μ F is usually large
enough to provide good stability. Increasing the output
capacitor above 10 μ F further improves stability. In order
to insure stability, a feedback capacitor is needed between
the output pin and the feedback pin. This is because stray
capacitance can form another pole with the large value of
feedback resistors used with the LT1020. Also, a feedback
capacitor minimizes noise pickup and improves ripple
rejection.
With the large dynamic operating range of the output
current, 10000:1, frequency response changes widely.
Low AC impedance capacitors are needed to insure stabil-
ity. While solid tantalum are best, aluminum electrolytics
can be used but larger capacitor values may be needed.
The CURRENT LIMIT pin allows one of the internal nodes
to be rolled off with a 0.05 μ F capacitor to ground. With this
LT1020
REF
V OUT
FB
2
11
0.001 μ F
+
10 μ F
capacitor, lower values of regulator output capacitance
can be used (down to 1 μ F) for low (<20mA) output
currents. Values of capacitance greater than 0.05 μ F de-
grade the transient response, so are not recommended.
4
*
* DIODE ADDS FEEDBACK
1020 F02
If the CURRENT LIMIT pin is connected to GND, the
current limit is decreased and only a 1 μ F output capacitor
is needed.
Figure 2. Minimizing Oscillation in Thermal Shutdown
When bypassing the reference, a 20 ? resistor must be
connected in series with the capacitor.
sn1020 1020fcs
8
相关PDF资料 |
PDF描述 |
|---|---|
| LT1026IS8#TRPBF | IC REG SWITCHD CAP DBL INV 8SOIC |
| LT1033CP | IC REG LDO NEG ADJ TO3P-3 |
| LT1054MJ8 | IC REG SWITCHD CAP DBL INV 8-DIP |
| LT1071CK | IC REG MULTI CONFIG ADJ TO220-5 |
| LT1072CSW#PBF | IC REG MULTI CONFIG ADJ 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1020MJ | 制造商:Linear Technology 功能描述:LDO Regulator Pos 0.125A 14-Pin CDIP |
| LT1020MJ883C | 制造商:LT 功能描述:New |
| LT1021BCH-5 | 功能描述:IC VREF SERIES BURIED ZENER TO-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 电压基准 系列:- 标准包装:2,000 系列:- 基准类型:旁路，可调节，精度 输出电压:1.24 V ~ 16 V 容差:±0.5% 温度系数:- 输入电压:1.24 V ~ 16 V 通道数:1 电流 - 阴极:100µA 电流 - 静态:- 电流 - 输出:20mA 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:TO-226-3、TO-92-3（TO-226AA）成形引线 供应商设备封装:TO-92-3 包装:带卷 (TR) |
| LT1021BCN8-10 | 功能描述:IC VREF SERIES SHUNT ZNR 8-PDIP RoHS:否 类别:集成电路 (IC) >> PMIC - 电压基准 系列:- 标准包装:2,000 系列:- 基准类型:旁路，可调节，精度 输出电压:1.24 V ~ 16 V 容差:±0.5% 温度系数:- 输入电压:1.24 V ~ 16 V 通道数:1 电流 - 阴极:100µA 电流 - 静态:- 电流 - 输出:20mA 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:TO-226-3、TO-92-3（TO-226AA）成形引线 供应商设备封装:TO-92-3 包装:带卷 (TR) |
| LT1021BCN8-10#PBF | 功能描述:IC VREF SERIES SHUNT ZNR 8-PDIP RoHS:是 类别:集成电路 (IC) >> PMIC - 电压基准 系列:- 标准包装:3,000 系列:- 基准类型:旁路，精度 输出电压:3V 容差:±0.5% 温度系数:100ppm/°C 输入电压:- 通道数:1 电流 - 阴极:82µA 电流 - 静态:- 电流 - 输出:15mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-TSSOP（5 引线），SC-88A，SOT-353 供应商设备封装:SC-70-5 包装:带卷 (TR) 其它名称:296-20888-2 |
发布紧急采购，3分钟左右您将得到回复。