- 您现在的位置：买卖IC网 > PDF目录95793 > LT1027ECS8#PBF (LINEAR TECHNOLOGY CORP) 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 5 V, PDSO8 PDF资料下载
参数资料
| 型号： | LT1027ECS8#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 基准电压源/电流源 |
| 英文描述： | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 5 V, PDSO8 |
| 封装： | LEAD FREE, PLASTIC, SOIC-8 |
| 文件页数： | 5/8页 |
| 文件大小： | 210K |
| 代理商： | LT1027ECS8#PBF |
LT1027
5
sn1027 1027fcs
U
S
A
O
PPLICATI
WU
U
I FOR ATIO
to approximately 1.2
VRMS in a 10Hz to 1kHz bandwidth.
Transient response is not affected by this capacitor. Start-
up settling time will increase to several milliseconds due
to the 7k
impedance looking into the NR pin. The
capacitor
must be a low leakage type. Electrolytics are not
suitable for this application. Just 100nA leakage current
will result in a 150ppm error in output voltage. This pin is
the most sensitive pin on the device. For maximum protec-
tion a guard ring is recommended. The ring should be
driven from a resistive divider from VOUT set to 4.4V (the
open-circuit voltage on the NR pin).
Transient Response
The LT1027 has been optimized for transient response.
Settling time is under 2
s when an AC-coupled 10mA load
transient is applied to the output. The LT1027 achieves
fast settling by using a class B NPN/PNP output stage.
When sinking current, the device may oscillate with ca-
pacitive loads greater than 100pF. The LT1027 is stable
with all capacitive loads when at no DC load or when
sourcing current, although for best settling time either no
output bypass capactor or a 4.7
F tantalum unit is recom-
mended. An 0.1
F ceramic output capacitor will maximize
output ringing and is not recommended.
Kelvin Connections
Although the LT1027 does not have true force-sense
capability, proper hook-up can improve line loss and
ground loop problems significantly. Since the ground pin
of the LT1027 carries only 2mA, it can be used as a low-
side sense line, greatly reducing ground loop problems on
the low side of the reference. The VOUT pin should be close
to the load or connected via a heavy trace as the resistance
of this trace directly affects load regulation. It is important
to remember that a 1.22mV drop due to trace resistance is
equivalent to a 1LSB error in a 5VFS, 12-bit system.
The circuits in Figures 2 and 3 illustrate proper hook-up to
minimize errors due to ground loops and line losses.
Losses in the output lead can be further reduced by adding
a PNP boost transistor if load current is 5mA or higher. R2
can be added to further reduce current in the output sense
load.
Effect of Reference Drift on System Accuracy
A large portion of the temperature drift error budget in
many systems is the system reference voltage. Figure 1
indicates the maximum temperature coefficient allowable
if the reference is to contribute no more than 0.5LSB error
to the overall system performance. The example shown is
a 12-bit system designed to operate over a temperature
range from 25
°C to 65°C. Assuming the system calibra-
tion is performed at 25
°C, the temperature span is 40°C.
It can be seen from the graph that the temperature coeffi-
cient of the reference must be no worse than 3ppm/
°C if
it is to contribute less than 0.5LSB error. For this reason,
the LT1027 has been optimized for low drift.
Figure 1. Maximum Allowable Reference Drift
Trimming Output Voltage
The LT1027 has an adjustment pin for trimming output
voltage. The impedance of the VADJ pin is about 20k with
an open-circuit voltage of 2.5V. A
±30mV guaranteed trim
range is achievable by tying the VADJ pin to the wiper of a
10k potentiometer connecting between the output and
ground. Trimming output voltage does not affect the TC of
the device.
Noise Reduction
The positive input of the internal scaling amplifier is
brought out as the Noise Reduction (NR) pin. Connecting
a 1
F Mylar capacitor between this pin and ground will
reduce the wideband noise of the LT1027 from 2.0
VRMS
TEMPERATURE SPAN (
°C)
10
0
MAXIMUM
TEMPERATURE
COEFFICIENT
FOR
0.5LSB
ERROR
(ppm/
°C)
30
100
1027 AI01
1.0
10
20
100
90
80
70
60
50
40
8-BIT
10-BIT
12-BIT
14-BIT
相关PDF资料 |
PDF描述 |
|---|---|
| LT1054IJ8 | SWITCHED CAPACITOR REGULATOR, CDIP8 |
| LT1073CS8-3.3#TR | SWITCHING REGULATOR, PDSO8 |
| LT1082MK/883B | 3 A SWITCHING REGULATOR, 75 kHz SWITCHING FREQ-MAX, MBFM2 |
| LT1082MK | 1 A SWITCHING REGULATOR, 60 kHz SWITCHING FREQ-MAX, MBFM2 |
| LT1176CS-5#TR | 1.2 A SWITCHING REGULATOR, 100 kHz SWITCHING FREQ-MAX, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1028ACJ8 | 制造商:Linear Technology 功能描述:OP Amp Single GP ±22V 8-Pin CDIP 制造商:Linear Technology 功能描述:OP Amp Single GP 22V 8-Pin CDIP 制造商:Linear Technology 功能描述:OP Amp Single GP ??22V 8-Pin CDIP |
| LT1028ACN8 | 功能描述:IC OP-AMP LOW NOISE SNGL 8-DIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| LT1028ACN8#PBF | 功能描述:IC OP-AMP LOW NOISE SNGL 8-DIP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| LT1028ACN8PBF | 制造商:Linear Technology 功能描述:Single precision op amp,LT1028ACN8 DIP8 |
| LT1028CN8 | 功能描述:IC OP-AMP LOW NOISE SNGL 8-DIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:13 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:65pA 电压 - 输入偏移:3000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。