参数资料
| 型号： | LT1028CSW |
| 厂商： | Linear Technology |
| 文件页数： | 3/28页 |
| 文件大小： | 0K |
| 描述： | IC OP-AMP LOW NOISE SNGL 16-SOIC |
| 标准包装： | 47 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 转换速率： | 15 V/µs |
| 增益带宽积： | 75MHz |
| 电流 - 输入偏压： | 30nA |
| 电压 - 输入偏移： | 20µV |
| 电流 - 电源： | 7.6mA |
| 电压 - 电源，单路/双路(±)： | ±4 V ~ 18 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SO |
| 包装： | 管件 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT1028/LT1128
11
1028fb
applicaTions inForMaTion – noise
Voltage Noise vs Current Noise
The LT1028/LT1128’s less than 1nV/√Hz voltage noise is
three times better than the lowest voltage noise heretofore
available (on the LT1007/1037). A necessary condition for
such low voltage noise is operating the input transistors at
nearly 1mA of collector currents, because voltage noise is
inversely proportional to the square root of the collector
current. Current noise, however, is directly proportional
to the square root of the collector current. Consequently,
the LT1028/LT1128’s current noise is significantly higher
than on most monolithic op amps.
Therefore, to realize truly low noise performance it is
important to understand the interaction between voltage
noise (en), current noise (In) and resistor noise (rn).
Total Noise vs Source Resistance
The total input referred noise of an op amp is given by:
et = [en2 + rn2 + (InReq)2]1/2
where Req is the total equivalent source resistance at the
two inputs, and
rn = √4kTReq = 0.13√Req in nV/√Hz at 25°C
As a numerical example, consider the total noise at 1kHz
of the gain 1000 amplifier shown in Figure 1.
the largest term, as in the example above, and the LT1028/
LT1128’s voltage noise becomes negligible. As Req is
further increased, current noise becomes important. At
1kHz, when Req is in excess of 20k, the current noise
component is larger than the resistor noise. The total
noise versus matched source resistance plot illustrates
the above calculations.
The plot also shows that current noise is more dominant
at low frequencies, such as 10Hz. This is because resistor
noise is flat with frequency, while the 1/f corner of current
noise is typically at 250Hz. At 10Hz when Req > 1k, the
current noise term will exceed the resistor noise.
When the source resistance is unmatched, the total noise
versus unmatched source resistance plot should be con-
sulted. Note that total noise is lower at source resistances
below 1k because the resistor noise contribution is less.
When RS > 1k total noise is not improved, however. This
is because bias current cancellation is used to reduce
input bias current. The cancellation circuitry injects two
correlated current noise components into the two inputs.
With matched source resistors the injected current noise
creates a common-mode voltage noise and gets rejected
by the amplifier. With source resistance in one input only,
the cancellation noise is added to the amplifier’s inherent
noise.
In summary, the LT1028/LT1128 are the optimum am-
plifiers for noise performance, provided that the source
resistanceiskeptlow.Thefollowingtabledepictswhichop
amp manufactured by Linear Technology should be used
to minimize noise, as the source resistance is increased
beyond the LT1028/LT1128’s level of usefulness.
Table 1. Best Op Amp for Lowest Total Noise vs Source Resistance
SOURCE RESIS-
TANCE (Ω) (Note 1)
BEST OP AMP
AT LOW FREQ (10Hz)
WIDEBAND (1kHz)
0 to 400
LT1028/LT1128
400 to 4k
LT1007/1037
LT1028/LT1128
4k to 40k
LT1001
LT1007/LT1037
40k to 500k
LT1012
LT1001
500k to 5M
LT1012 or LT1055
LT1012
>5M
LT1055
Note 1: Source resistance is defined as matched or unmatched, e.g.,
RS = 1k means: 1k at each input, or 1k at one input and zero at the other.
Req = 100Ω + 100Ω || 100k ≈ 200Ω
rn = 0.13√200 = 1.84nV√Hz
en = 0.85nV√Hz
In = 1.0pA/√Hz
et = [0.852 + 1.842 + (1.0 × 0.2)2]1/2 = 2.04nV/√Hz
Output noise = 1000 et = 2.04V/√Hz
At very low source resistance (Req < 40Ω) voltage noise
dominates. As Req is increased resistor noise becomes
–
+
100
100k
100
LT1028
LT1128
1028 F01
Figure 1
相关PDF资料 |
PDF描述 |
|---|---|
| MCP6002T-I/SN | IC OPAMP 1.8V 1MHZ DUAL 8-SOIC |
| LT1469CN8#PBF | IC OPAMP 16BIT DUAL 90MHZ 8DIP |
| 77315-101-08LF | BERGSTIK |
| 75160-118-09LF | BERGSTIK |
| 961128-6404-AR | CONN HEADER VERT SGL 28POS GOLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1028CSW#PBF | 功能描述:IC OP-AMP LOW NOISE SNGL 16-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:13 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:65pA 电压 - 输入偏移:3000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
| LT1028CSW#TR | 功能描述:IC OP AMP LOW NOISE HS 16SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:150 系列:- 放大器类型:音频 电路数:2 输出类型:- 转换速率:5 V/µs 增益带宽积:12MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:500µV 电流 - 电源:6mA 电流 - 输出 / 通道:50mA 电压 - 电源，单路/双路(±):4 V ~ 32 V，±2 V ~ 16 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| LT1028CSW#TRPBF | 功能描述:IC OP-AMP LOW NOISE SNGL 16-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:150 系列:- 放大器类型:音频 电路数:2 输出类型:- 转换速率:5 V/µs 增益带宽积:12MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:500µV 电流 - 电源:6mA 电流 - 输出 / 通道:50mA 电压 - 电源，单路/双路(±):4 V ~ 32 V，±2 V ~ 16 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| LT1029ACH | 制造商:Linear Technology 功能描述:V-Ref Precision 5V 10mA 3-Pin TO-46 |
| LT1029ACZ | 功能描述:IC VREF SHUNT 5V TO-92-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 电压基准 系列:- 产品培训模块:Voltage Reference Basics 标准包装:100 系列:- 基准类型:旁路，精度 输出电压:4.096V 容差:±0.075% 温度系数:50ppm/°C 输入电压:- 通道数:1 电流 - 阴极:1µA 电流 - 静态:- 电流 - 输出:10mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。