- 您现在的位置：买卖IC网 > PDF目录14798 > LT1076CR#PBF (Linear Technology)IC REG MULTI CONFIG ADJ 2A D2PAK PDF资料下载
参数资料
| 型号： | LT1076CR#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 5/16页 |
| 文件大小： | 0K |
| 描述： | IC REG MULTI CONFIG ADJ 2A D2PAK |
| 标准包装： | 50 |
| 类型： | 降压（降压），升压（升压），反相，回扫 |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.5 V ~ 50 V |
| 输入电压： | 8 V ~ 45 V |
| 频率 - 开关： | 100kHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-8，D²Pak（7 引线+接片），TO-263CA |
| 包装： | 管件 |
| 供应商设备封装： | D2PAK-7 |
| 产品目录页面： | 1325 (CN2011-ZH PDF) |
LT1074/LT1076
BLOCK DIAGRA
DESCRIPTIO
A switch cycle in the LT1074 is initiated by the oscillator
setting the R/S latch. The pulse that sets the latch also
locks out the switch via gate G1. The effective width of this
pulse is approximately 700ns, which sets the maximum
switch duty cycle to approximately 93% at 100kHz switch-
ing frequency. The switch is turned off by comparator C1,
which resets the latch. C1 has a sawtooth waveform as one
input and the output of an analog multiplier as the other
input. The multiplier output is the product of an internal
reference voltage, and the output of the error amplifier, A1,
divided by the regulator input voltage. In standard buck
regulators, this means that the output voltage of A1
required to keep a constant regulated output is indepen-
dent of regulator input voltage. This greatly improves line
transient response, and makes loop gain independent of
input voltage. The error amplifier is a transconductance
type with a G M at null of approximately 5000 μ mho. Slew
current going positive is 140 μ A, while negative slew
current is about 1.1mA. This asymmetry helps prevent
overshoot on start-up. Overall loop frequency compensa-
tion is accomplished with a series RC network from V C to
ground.
Switch current is continuously monitored by C2, which
resets the R/S latch to turn the switch off if an overcurrent
condition occurs. The time required for detection and
switch turn off is approximately 600ns. So minimum
switch “on” time in current limit is 600ns. Under dead
shorted output conditions, switch duty cycle may have to
be as low as 2% to maintain control of output current. This
would require switch on time of 200ns at 100kHz switch-
voltages by feeding the FB signal into the oscillator and
creating a linear frequency downshift when the FB signal
drops below 1.3V. Current trip level is set by the voltage on
the I LIM pin which is driven by an internal 320 μ A current
source. When this pin is left open, it self-clamps at about
4.5V and sets current limit at 6.5A for the LT1074 and 2.6A
for the LT1076. In the 7-pin package an external resistor
can be connected from the I LIM pin to ground to set a lower
current limit. A capacitor in parallel with this resistor will
soft-start the current limit. A slight offset in C2 guarantees
that when the I LIM pin is pulled to within 200mV of ground,
C2 output will stay high and force switch duty cycle to zero.
The “Shutdown” pin is used to force switch duty cycle to
zero by pulling the I LIM pin low, or to completely shut down
the regulator. Threshold for the former is approximately
2.35V, and for complete shutdown, approximately 0.3V.
Total supply current in shutdown is about 150 μ A. A 10 μ A
pull-up current forces the shutdown pin high when left
open. A capacitor can be used to generate delayed start-
up. A resistor divider will program “undervoltage lockout”
if the divider voltage is set at 2.35V when the input is at the
desired trip point.
The switch used in the LT1074 is a Darlington NPN (single
NPN for LT1076) driven by a saturated PNP. Special
patented circuitry is used to drive the PNP on and off very
quickly even from the saturation state. This particular
switch arrangement has no “isolation tubs” connected to
the switch output, which can therefore swing to 40V below
ground.
ing frequency, so frequency is reduced at very low output
sn1074 1074fds
5
相关PDF资料 |
PDF描述 |
|---|---|
| GSC06DTEF | CONN EDGECARD 12POS .100 EYELET |
| MAX6424UK36+T | IC MPU/RESET CIRC 3.60V SOT23-5 |
| PM1812-R68K | INDUCTOR .68UH 10% 1812 SMD |
| GEC44DRTF | CONN EDGECARD 88POS DIP .100 SLD |
| SLPX182M160H5P3 | CAP ALUM 1800UF 160V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1076CT | 功能描述:IC REG MULTI CONFIG ADJ TO220-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1076CT#06 | 制造商:Linear Technology 功能描述:Step-Down Switching Regulator |
| LT1076CT#06PBF | 功能描述:IC REG MULTI CONFIG ADJ TO220-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LT1076CT#06PBF | 制造商:Linear Technology 功能描述:IC DC-DC CONV BUCK 100KHZ 制造商:Linear Technology 功能描述:IC, DC-DC CONV, BUCK, 100KHZ, 2.6A, TO-2 |
| LT1076CT#30PBF | 制造商:Linear Technology 功能描述:IC REG MULTI CONFIG ADJ TO220-5 |
发布紧急采购，3分钟左右您将得到回复。