参数资料
| 型号： | LT1079CN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/20页 |
| 文件大小： | 0K |
| 描述： | IC PREC OPAMP MICRPWR QUAD 14DIP |
| 标准包装： | 25 |
| 放大器类型： | 通用 |
| 电路数： | 4 |
| 转换速率： | 0.1 V/µs |
| 增益带宽积： | 200kHz |
| 电流 - 输入偏压： | 7nA |
| 电压 - 输入偏移： | 70µV |
| 电流 - 电源： | 47µA |
| 电压 - 电源，单路/双路(±)： | 2.2 V ~ 30 V，±1.1 V ~ 15 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 14-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-PDIP |
| 包装： | 管件 |
| 产品目录页面： | 1317 (CN2011-ZH PDF) |
11
LT1078/LT1079
10789fe
APPLICATIONS INFORMATION
WU
U
difference is critical because in many applications these
competing devices cannot be operated as micropower op
amps and swing to ground simultaneously.
As an example, consider the instrumentation amplifier
shown on the front page. When the common mode signal
is low and the output is high, amplifier A has to sink
current. When the common mode signal is high and the
output low, amplifier B has to sink current. The competing
devices require a 12k pull-down resistor at the output of
amplifier A and a 15k at the output of B to handle the
specified signals. (The LT1078 does not need pull-down
resistors.) When the common mode input is high and the
output is high these pull-down resistors draw 300
μA (150μA
each), which is excessive for micropower applications.
The instrumentation amplifier is by no means the only
application requiring current sinking capability. In seven
of the nine single supply applications shown in this data
sheet the op amps have to be able to sink current. In two
of the applications the first amplifier has to sink only the
6nA input bias current of the second op amp. The compet-
ing devices, however, cannot even sink 6nA without a pull-
down resistor
Since the output of the LT1078/LT1079 cannot go exactly
to ground, but can only approach ground to within a few
millivolts, care should be exercised to ensure that the
output is not saturated. For example, a 1mV input signal
will cause the amplifier to set up in its linear region in the
gain 100 configuration shown in Figure 1a, but is not
Single supply operation can also create difficulties at the
input. The driving signal can fall below 0V — inadvertently
or on a transient basis. If the input is more than a few
hundred millivolts below ground, two distinct problems
can occur on previous single supply designs, such as the
LM124, LM158, OP-20, OP-21, OP-220, OP-221, OP-420
(1 and 2), OP-90/290/490 (2 only):
1. When the input is more than a diode drop below ground,
unlimited current will flow from the substrate (V –
terminal) to the input. This can destroy the unit. On the
LT1078/LT1079, resistors in series with the input protect
the devices even when the input is 5V below ground.
2. When the input is more than 400mV below ground (at
25
°C), the input stage saturates and phase reversal
occurs at the output. This can cause lockup in servo
systems. Due to a unique phase reversal protection cir-
cuitry, the LT1078/LT1079 output does not reverse, as
illustrated in Figure 2, even when the inputs are at – 1V.
enough to make the amplifier function properly in the
voltage follower mode, Figure 1b.
Figure 1a. Gain 100 Amplifier
+
–
5V
1mV
R
99R
100mV
LT1078/79 F01a
+
–
5V
1mV
R
99R
100mV
LT1078/79 F01a
Figure 1b. Voltage Follower
Figure 2. Voltage Follower with Input Exceeding the Negative Common Mode Range (VS = 5V, 0V)
2V
0V
6VP-P INPUT
1ms/DIV
–1V TO 5V
LT1078/79 F02a
1ms/DIV
LT1078/LT1079 NO PHASE REVERSAL
LT1078/79 F02C
2V
0V
4V
1ms/DIV
OP-90 EXHIBITS OUTPUT PHASE REVERSAL
LT1078/79 F02b
2V
0V
4V
相关PDF资料 |
PDF描述 |
|---|---|
| LT6600IS8-20#PBF | IC AMP DIFF LP FLTR 20MHZ 8-SOIC |
| LT1361CS8#PBF | IC OP-AMP HI-SPD 50MHZ DUAL8SOIC |
| M90-7011245 | CONN PLUG PNL MNT AU 12POS |
| LT1126CS8#PBF | IC OP-AMP DECOMPENSAT DUAL 8SOIC |
| M80-5S22005MQ | CONN HDR 2MM R/A W/SCREW 20POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1079IN | 功能描述:IC PREC OPAMP MICRPWR QUAD 14DIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:13 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:65pA 电压 - 输入偏移:3000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
| LT1079IN#PBF | 功能描述:IC PREC OPAMP MICRPWR QUAD 14DIP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| LT1079IN#PBF | 制造商:Linear Technology 功能描述:IC OP-AMP QUAD 200KHZ 0.1V 制造商:Linear Technology 功能描述:IC, OP-AMP, QUAD, 200KHZ, 0.1V/s, 150V |
| LT1079IS | 制造商:Linear Technology 功能描述:Operational Amplifier, Quad AMP, Bipolar, 16 Pin, Plastic, SOP |
| LT1079ISW | 功能描述:IC PREC OP-AMP MCRPWR QUAD16SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:3.5 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:30pA 电压 - 输入偏移:2000µV 电流 - 电源:200µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。