参数资料
| 型号： | LT1086IT-3.3 |
| 厂商： | Linear Technology |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V 1.5A TO220 |
| 标准包装： | 50 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 最高 20V |
| 电压 - 压降（标准）： | 1.3V @ 1.5A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1.5A |
| 电流 - 限制（最小）： | 1.5A |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 通孔 |
| 封装/外壳： | TO-220-3 |
| 供应商设备封装： | TO-220-3 |
| 包装： | 管件 |
LT1086 Series
APPLICATIO N S I N FOR M ATIO N
The LT1086 family of 3-terminal regulators is easy to use
and has all the protection features that are expected in high
performance voltage regulators. They are short-circuit
protected and have safe area protection as well as thermal
shutdown to turn off the regulator should the temperature
exceed about 165 ° C at the sense point.
These regulators are pin compatible with older 3-terminal
adjustable devices, offer lower dropout voltage and more
precise reference tolerance. Further, the reference stabil-
ity with temperature is improved over older types of
regulators. The only circuit difference between using the
LT1086 family and older regulators is that they require an
output capacitor for stability.
Stability
The circuit design used in the LT1086 family requires the
use of an output capacitor as part of the device frequency
compensation. For all operating conditions, the addition of
150 μ F aluminum electrolytic or a 22 μ F solid tantalum on
the output will ensure stability. Normally capacitors much
smaller than this can be used with the LT1086. Many
different types of capacitors with widely varying charac-
teristics are available. These capacitors differ in capacitor
tolerance (sometimes ranging up to ± 100%), equivalent
series resistance, and capacitance temperature coeffi-
cient. The 150 μ F or 22 μ F values given will ensure stability.
When using the LT1086 the adjustment terminal can be
bypassed to improve ripple rejection. When the adjust-
ment terminal is bypassed the requirement for an output
capacitor increases. The values of 22 μ F tantalum or 150 μ F
aluminum cover all cases of bypassing the adjustment
terminal. For fixed voltage devices or adjustable devices
without an adjust pin bypass capacitor, smaller output
capacitors can be used with equally good results. The table
below shows approximately what size capacitors are needed
to ensure stability.
response with heavy load current changes. Output capaci-
tance can be increased without limit and larger values of
output capacitor further improve stability and transient
response of the LT1086 regulators.
Another possible stability problem that can occur in mono-
lithic IC regulators is current limit oscillations. These can
occur because in current limit, the safe area protection
exhibits a negative impedance. The safe area protection
decreases the current limit as the input-to-output voltage
increases.That is the equivalent of having a negitive resis-
tance since increasing voltage causes current to decrease.
Negative resistance during current limit is not unique to
the LT1086 series and has been present on all power IC
regulators. The value of negative resistance is a function of
how fast the current limit is folded back as input-to-output
voltage increases. This negative resistance can react with
capacitors or inductors on the input to cause oscillation
during current limiting. Depending on the value of series
resistance, the overall circuitry may end up unstable. Since
this is a system problem, it is not necessarily easy to solve;
however, it does not cause any problems with the IC
regulator and can usually be ignored.
Protection Diodes
In normal operation the LT1086 family does not need any
protection diodes. Older adjustable regulators required
protection diodes between the adjustment pin and the
output and from the output to the input to prevent over-
stressing the die. The internal current paths on the LT1086
adjustment pin are limited by internal resistors. Therefore,
even with capacitors on the adjustment pin, no protection
diode is needed to ensure device safety under short-circuit
conditions.
Diodes between input and output are usually not needed.
The internal diode between the input and the output pins
of the LT1086 family can handle microsecond surge
Recommended Capacitor Values
INPUT OUTPUT
10 μ F 10 μ F Tantalum, 50 μ F Aluminum
10 μ F 22 μ F Tantalum, 150 μ F Aluminum
ADJUSTMENT
None
20 μ F
currents of 10A to 20A. Even with large output capaci-
tances, it is very difficult to get those values of surge
currents in normal operation. Only with high value output
capacitors such as 1000 μ F to 5000 μ F, and with the input
pin instantaneously shorted to ground, can damage occur.
Normally, capacitor values on the order of 100 μ F are used
in the output of many regulators to ensure good transient
A crowbar circuit at the input of the LT1086 can generate
those kinds of currents and a diode from output to input is
then recommended. Normal power supply cycling or even
sn1086 1086ffs
8
相关PDF资料 |
PDF描述 |
|---|---|
| GCB110DHFD | CONN CARDEDGE 220POS .050" SMD |
| RYM36DRMT-S664 | CONN EDGECARD 72POS .156 WW |
| LT1521CS8-5 | IC REG LDO 5V .3A 8-SOIC |
| RYM22DRMT-S273 | CONN EDGECARD 44POS .156 SQ WW |
| RSM22DRMT-S273 | CONN EDGECARD 44POS .156 SQ WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1086IT-5 | 功能描述:IC REG LDO 5V 1.5A TO220 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
| LT1086IT-5#PBF | 功能描述:IC REG LDO 5V 1.5A TO220 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:800 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:最高 16V 电压 - 压降（标准）:0.7V @ 4A 稳压器数量:1 电流 - 输出:4A 电流 - 限制（最小）:4.2A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263-5 包装:带卷 (TR) 其它名称:AP1184K525L-13AP1184K525LDITR |
| LT1086MH/883 | 制造商:Linear Technology 功能描述:POWER SUPPLY-VOLTAGE REGULATOR |
| LT1086MK/883 | 制造商:undefined 功能描述: |
| LT1086MK-12 | 功能描述:IC REG LDO 12V 1.5A TO-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式和可调式 输出电压:3.3V，1.25 V ~ 5.7 V 输入电压:4.5 V ~ 7 V 电压 - 压降（标准）:1.1V @ 1A 稳压器数量:2 电流 - 输出:1A 电流 - 限制（最小）:1A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-252-5，DPak（4 引线 + 接片），TO-252AD 供应商设备封装:PPAK 包装:管件 其它名称:497-3576-5 |
发布紧急采购，3分钟左右您将得到回复。