参数资料
| 型号： | LT1102CN8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC PREC INSTRMNT-AMP JFET 8-DIP |
| 标准包装： | 50 |
| 放大器类型： | 仪表 |
| 电路数： | 1 |
| 转换速率： | 30 V/µs |
| 增益带宽积： | 3.5MHz |
| 电流 - 输入偏压： | 4pA |
| 电压 - 输入偏移： | 200µV |
| 电流 - 电源： | 3.4mA |
| 电压 - 电源，单路/双路(±)： | ±9 V ~ 18 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 产品目录页面： | 1323 (CN2011-ZH PDF) |
LT1102
5
1102fb
ELECTRICAL CHARACTERISTICS
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: This parameter is tested on a sample basis only.
Note 3: Current noise is calculated from the formula:
in = (2qIB)1/2
where q = 1.6 10–19 coulomb. The noise of source resistors up to 1G
Ω
swamps the contribution of current noise.
Note 4: This parameter is not tested. It is guaranteed by design and by
inference from the slew rate measurement.
Note 5: Overdrive recovery is defined as the time delay from the removal
of an input overdrive to the output’s return from saturation to linear
operation.
50% overdrive equals VIN = ±2V (G = 10) or VIN = ±200mV (G = 100).
Note 6: This parameter is not tested. It is guaranteed by design and by
inference from other tests.
TYPICAL PERFOR A CE CHARACTERISTICS
UW
Small Signal Response, G = 10
(Input = 50mV Pulse)
Small Signal Response, G = 100
(Input = 5mV Pulse)
Slew Rate, G = 100
(Input =
±130mV Pulse)
Settling Time, G = 10
(Input From – 10V to 10V)
Settling Time, G = 10
(Input From 10V to –10V)
Settling Time, G = 100
(Input From – 10V to 10V)
2
μS/DIV
100mV/DIV
FPOLT1102 TPC01
2
μS/DIV
100mV/DIV
FPOLT1102 TPC02
2
μS/DIV
5V/DIV
FPOLT1102 TPC03
2
μS/DIV
5mV/DIV
AT
SUM
NODE
FPOLT1102 TPC07
1
μS/DIV
5mV/DIV
AT
SUM
NODE
FPOLT1102 TPC04
1
μS/DIV
5mV/DIV
AT
SUM
NODE
FPOLT1102 TPC05
2
μS/DIV
5mV/DIV
AT
SUM
NODE
FPOLT1102 TPC06
Settling Time, G = 100
(Input From 10V to –10V)
相关PDF资料 |
PDF描述 |
|---|---|
| LT1007ACN8#PBF | IC PREC OP-AMP HI-SPD SNGL 8-DIP |
| LTC2053HDD#PBF | IC AMP INST 0-DRFT R-R I/O 8-DFN |
| AD8610ARZ | IC OPAMP JFET 25MHZ PREC 8SOIC |
| SY88303BLMG | IC AMP CML LIMITING POST 16-MLF |
| AD626ANZ | IC AMP DIFF LP 12MA 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1102I | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Speed, Precision, JFET Input Instrumentation Amplifier(Fixed Gain=10 or 100) |
| LT1102IN8 | 功能描述:IC PREC INSTRMNT-AMP JFET 8-DIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:150 系列:- 放大器类型:音频 电路数:2 输出类型:- 转换速率:5 V/µs 增益带宽积:12MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:500µV 电流 - 电源:6mA 电流 - 输出 / 通道:50mA 电压 - 电源，单路/双路(±):4 V ~ 32 V，±2 V ~ 16 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| LT1102IN8#PBF | 功能描述:IC PREC INSTRMNT-AMP JFET 8-DIP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:150 系列:- 放大器类型:音频 电路数:2 输出类型:- 转换速率:5 V/µs 增益带宽积:12MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:500µV 电流 - 电源:6mA 电流 - 输出 / 通道:50mA 电压 - 电源，单路/双路(±):4 V ~ 32 V，±2 V ~ 16 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| LT1102M | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Speed, Precision, JFET Input Instrumentation Amplifier(Fixed Gain=10 or 100) |
| LT1102MH | 制造商:Linear Technology 功能描述:SP Amp INSTR Amp Single ±20V 8-Pin TO-5 |
发布紧急采购，3分钟左右您将得到回复。